Three steel bolts are to be used to attach the steel plate shown to a wooden beam. The plate will support a 110kN and the ultimate shearing stress for the steel used is 360MPA and that a factor of safety of 3.35 is desired, determine the increase in the bolt diameter required if an additional 100kN load is added to the existing 11OKN.

Three steel bolts are to be used to attach the steel plate shown to a wooden beam. The plate will support a 110kN and the ultimate shearing stress for the steel used is 360MPA and that a factor of safety of 3.35 is desired, determine the increase in the bolt diameter required if an additional 100kN load is added to the existing 11OKN.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Similar questions

Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
Three steel bolts are to be used to attach thesteel plate shown to a wooden beam. Theplate will support a 110kN and the ultimateshearing stress for the steel used is 360MPaand that a factor of safety of 3.35 is desired,determine the increase in the bolt diameterrequired if an additional 100kN load is addedto the existing 110kN.
Urgent Given the following data for a rectangular beam, b = 320 mm, d = 520 mm, f’c = 27 MPa, fy = 345 MPa.Dead Load Moment = 180 kN-m, Live Load Moment = 167 kN-m. Determine the required tension steelarea. (answer with complete solution) Final answer must be: Mu = 483.2 kN-m, FMnmax = 487.31 kN-m, c = 208.8 mm, As = 3,777 mm2
: Verify, using appropriate Chapter E design provisions, the tabularized (Table 4-7) buckling capacity of a WT6X20 for both the x- and y-axes at (KL)x = (KL)y = (KL)z = 10 ft. Assume A992 steel.
The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmas TIN EA). 2. IfG =30 GPa find the angle of twist at the free end of beam. 10 KN
The section shown carries a total service tension load of 508 kNwith a dead to live load ratio of 2:3. If the tension member has a length of 3 meters and A36steel, determine the following: a. The effective net area b. The LRFD design strength c. The ASD design strength d. Is the section adequate? section: C15 x 40 value of S: 63
Problem 1. A W30 x 116 beam hasthe top flange restrained againstlateral displacement and rotationand has an unstiffened web. A pointload is applied to the top flange at2m. From the left support. The beamspans 12 m. Use A36 steel with yieldstrength of Fy = 248 Mpa. a. Compute the maximum value of point loadthat may be applied without web yieldingoccurring. b. Compute the maximum value of point loadthat may be applied without web cripplingoccurring. Properties of W30 x 116d = 762 mmK = 41.28 mmbf = 266.7 mmtf = 21.59 mmtw = 14.33 mm
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.
If the allowable bearing stress in the bolt is 18.855 ksi. what is the minimumrequired diameter of the bolt at B? b= .75” h= 7.874” Distances are in feet.
The unknown load P is acting eccentrically with respect to the horizontal and vertical axes of the I-section shown. Knowing that the horizontal eccentricity is a = 1.25 in. and the vertical eccentricity is 2.5 in. determine the largest value of P that can be applied without exceeding either of the following tensile andcompressive allowable stresses:σten = 10 ksiσcomp = 18 ksi
The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited to 255 MPa, determine the minimum bolt diameter that may be used in the connection.
Determine if the channel is adequate for the tension load Pu = 420 kN as shown. The channel is ASTM A-36 steel (Fy = 248 MPa, Fu = 400 MPa) and it is connected with four 16 mm diameter bolts. Determine the block shear strength of the section. Ubs = 1.0 Determine the strength based on gross yielding. Determine the strength based on tensile ruptuture.