A rectangular block is 137 mm long in the Xdirection, 93 mm wide in the Y direction, and56 mm thick in the Z direction. The block issubjected to a triaxial loading of threeuniformly distributed forces as follows: 200kN tension in the X direction, 186 kN tensionin the Y direction, and 228 kN compression inthe Z direction. If v = 0.3 and E = 200 GPa,%3Ddetermine the single uniformly distributedload in the X direction that would producethe same deformation in the Z direction asthe original loading. Answer must be in kN. As shown, three steel wires, each 27 mm2 inarea, are used to lift a mass M. Theirunstretched lengths are 19.99 m, 19.98 m,and 20 m. If M= 979 kg. what stress existsin the MIDDLE wire? Use E=215 Gpa.Answer must be in MPa.

Strain will be equal in 1st and 2nd case as length is same. Comparing deformation and strain will…

A rectangular block is 137 mm long in the X direction, 93 mm wide in the Y direction, and 56 mm thick in the Z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 200 kN tension in the X direction, 186 kN tension in the Y direction, and 228 kN compression in the Z direction. If v = 0.3 and E = 200 GPa, %3D %3D determine the single uniformly distributed load in the X direction that would produce the same deformation in the Z direction as the original loading. Answer must be in kN.

A rectangular block is 137 mm long in the X direction, 93 mm wide in the Y direction, and 56 mm thick in the Z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 200 kN tension in the X direction, 186 kN tension in the Y direction, and 228 kN compression in the Z direction. If v = 0.3 and E = 200 GPa, %3D %3D determine the single uniformly distributed load in the X direction that would produce the same deformation in the Z direction as the original loading. Answer must be in kN.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.11P

See similar textbooks

Similar questions

Determine the normal stress in each of the cables? (MPa) a. 85.7 b. 75.7 c. 65.7 d. 55.7 If the cables elongated by 1 mm, what is the vertical displacement of the precasat slab? (mm) a. 1.758 b. 1.658 c. 1.458 d. 1.558 What is the tensile force in each of the cables? (kN) a. 5.98 b. 4.98 c. 7.98 d. 6.98 SOLVE ALL AND WILL GET A LIKE <3 ps: unit weight of concrete is 24kn/m^3
11-58. The measured strains for an equiangular rosette, attached to a stressed aluminum alloy member,are E0 = +400 micro m/m,E60 = +400 micro m/m, and E 120 = -600 micro m/m. What are the principal stresses and in which directions do they act?Given E =70 GPa, and v = 0.25.
A rectangular block is 123 mm long in the X direction, 82 mm wide in the Y direction, and 54 mm thick in the Z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 200 kN tension in the X direction, 194 kN tension in the Y direction, and 222 kN compression in the Z direction. If ν = 0.3 and E = 196 GPa, determine the single uniformly distributed load in the X direction that would produce the same deformation in the Z direction as the original loading. Answer must be in kN.
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa
The rectangular piece of wood, 76 mm by 174 mm, is used as a compression block. The grain of the wood makes a 30.3º angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 20.2 MPa. Round off the final answer to four decimal places.
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of thewhole structure which is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
A cantilever retaining wall supports 2 layers of soil and surcharge as shown below. The layers have these properties: Layer 1: 1.8m thick. γ = 17.4 kN/m3 and ϕ = 22 degrees Layer 2: 4.2m thick. γsat = 18.1 kN/m3 and ϕ = 30 degrees The angle of friction between the base and soil is 42 degrees. Unit weight of concrete is 23.6 kN/m3 What is the design moment (kNm / m) at the bottom of the stem? None of the choices 819.98 478.88 363.00 299.30 Please answer this asap. For upvote. Thank you very much
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
A large uniform cylindrical steel rod of density ρ = 8.8 g/cm3 is 4.0 m long and has a diameter of 5.0 cm. The rod is fastened to a concrete floor with its long axis vertical. What is the normal stress in the rod at the cross section located at (a) 2.0 m from its lower end? (b) 2.5m from the lower end? Your answer
A simply supported rectangular beam 50 mm wide by 100 mm deep, carries a uniformly distributed load of 1200 N/m over the entire length.1. Which of the following gives the max. length of the beam If the flexural stress is limited to 20 MPa. a. 3.11 m.b. 3.33 m.c. 3.44 m.d. 3.66 m.2. Which of the following gives the max. shearing stress of the beam. a. 0.30 MPab. 0.50 MPac. 0.40 MPad. 0.60 MPa3. Which of the following gives the max. deflection of the beam assuming E = 18000 MPa. a. 24.52 mmb. 25.72 mmc. 26.62 mmd. 28.82 mm
A 50 kg block has a coefficient friction of 0.30 Determine the force fricrion between A and B.