Three tanks containing brine are shown below. Construct a model for the number of pounds of salt x₁(t), x₂(t), x²(t) at time t in tanks A, B, and C respectively. Then write it in matrix form. You do not need to solve. mixture mixture 1 gal/min 2 gal/min មា ២ A 100 gal 100 gal pure water 4 gal/min mixture 6 gal/min B 100 gal mixture 5 gal/min mixture 4 gal/min

Three tanks containing brine are shown below. Construct a model for the number of pounds of salt x₁(t), x₂(t), x²(t) at time t in tanks A, B, and C respectively. Then write it in matrix form. You do not need to solve. mixture mixture 1 gal/min 2 gal/min មា ២ A 100 gal 100 gal pure water 4 gal/min mixture 6 gal/min B 100 gal mixture 5 gal/min mixture 4 gal/min

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 23P

See similar textbooks

Similar questions

Solve the following problem and result is: Specific gravity of the material is : 4.45 Empty weight of pycnometer : 529 grams Empty weight of pycnometer + weight of soil : W2 Empty weight of pycnometer + soil + water : 1539 grams Empty weight of pycnometer + fully filled water : 1387 grams what is the value of W2 ? Select one: O a. 712 grams O b. 733 grams O c. 725 grams O d. 693 grams
Problem 8: Inputs: ● FA = 125 lb FB = 75 lb Fc= 87 lb r = 3 in (radius to all load cells) FA X FC A 300 Z 0 FB B A circular plate is used in a machine called a compactor to determine the mechanical properties of various materials. In this particular test, three load cells are located at the same radial distance from point O. (Load cells measure force). If the load cells measure the forces shown above, determine the equivalent force system of a single force acting on the plate. Specifically: a) What is the x-coordinate of the point where the resultant force's line of action intersects the x-y plane? You must include sign, positive or negative. 30° b) What is the y-coordinate of the point where the resultant force's line of action intersects the x-y plane? You must include sign, positive or negative. y
The answer on letter B. MUST BE "q = 0.401 cm3/s/cm" kindly explain your solution thank you
The question refers to a well-mixed aeration pond or aeration lagoon that can be modeled according to the diagram below. The pond is simply a body of water that holds the wastewater for some detention time before the waste degrades or leaves in the effluent stream. There is no recycle line. You should derive a mass balance on X to solve these problems, make sure to include all terms in the mass balance. You may assume no X flows in with the influent. The perfectly mixed aeration pond with no recycle (return line) above serves as the biological reactor for a small community. The pond receives 30 m3/d of influent with a BOD5 of 350 mg/L that must be reduced to 20 mg/L before discharge. It has been found that the kinetic constants for the system are Ks=100mg/L BOD5, kd=0.10 d—1 , μm = 1.6 d—1 , and Y is 0.60 mg VSS/mg BOD5. Note: In this system each day, the bacteria have to grow at the same rate as they leave in the effluent, in order for the bacteria population to stay at a steady…
The question refers to a well-mixed aeration pond or aeration lagoon that can be modeled according to the diagram below. The pond is simply a body of water that holds the wastewater for some detention time before the waste degrades or leaves in the effluent stream. There is no recycle line. You should derive a mass balance on X to solve these problems, make sure to include all terms in the mass balance. You may assume no X flows in with the influent. A rectangular, well-mixed aeration lagoon that has the same conceptual model above is 60 m long, 5 m wide, and 2 m deep. It receives 400 m3/d of wastewater with a BOD5 of 336 mg BOD5/L for treatment. The biodegradation rate constants for the wastewater are yield coefficient = 0.8 mg VSS/mg BODs, endogenous decay constant = 0.08 d—1 , maximum specific microbial growth rate = 1.10 d—1 , and the half velocity constant = 76.0 mg BOD5/L. Note: BOD refers to substrate concentration and it also refers to how much O2 is required to consume the…
For the closed tank with Bourdon gauges tapped into it "see figure (2)", What is the specific gravity of the oil , and The pressure reading on gauge (C)?. PA=50kPa 0.5 m Air 1m Oil Pa 58.53kl 0.5 m 1m Water Pc=? kPa 0.5 m kak→→→→K→→→K Figure (2)
2. A cube of material is 4 in. on a side and floats at the interface between kerosene (SG=0.82) and water, as shown. a. Find the specific gravity of the material. b. How much weight is required to fully submerge the cube under water? (SG=0.973) (0.063 lb) Kerosene b/3 Water 2b/3 IPILX
Replace the force system acting on the beam by an equivalent resultant force, and specify its point of application on the beam measured from point O (Figure 1). Take F₁ = 5 lb, F2 = 10 lb, and F3 = 30 lb. ▼ Part A Determine the magnitude of the resultant force. Express your answer in pounds to three significant figures. 17 ΑΣΦ ↓↑ vec FR = Submit Request Answer ? lb
p (kPa) 200- V. V 2V, 3V, 圓
18. Calculate the pressure exerted by 4 kg mass of nitrogen gas at a temperature of 15°C if the volume is 0.35 m. Molecular weight of nitrogen is 28. 19. The pressure of a liquid is increased from 60 N/cm to 100 N/cm and volume decreases by 0.2 per cent. Determine the bulk modulus of elasticity. 20. Determine the bulk modulus of clasticit [Ans. 97.8 N/em] (Ans. 2x 10 Nem]
1. Estimate the vacuum pressure that should be created by a suction pump in order to lift a ground water which is 10m below the level ground. Neglect the effect of pipe friction. Explain the step by step solution, and draw a figure or free body diagram. 2. Three liquid substances of the same mass and have an S.G. of 1.20, 0.835 and 1.0 were being mixed to form a new compound. Estimate the resulting density. Explain the step by step solution, and draw a figure or free body diagram.
An amount of glycerin has a volume of 1 m' when the pressure is 120 kpa. If the pressure is increased to 400 kpa, determine the change in volume of this cubic meter. The bulk modulus for glycerin is E, = 4.52 GPa