THydropower Plant System The following nametag is specification of a generator in a hydropower plant. MITSUBISHI AC GENERATOR Output Voltage 4. 84.5 MVA 11 kV Current Frequency Speed Power Factor 4435 A 50 Hz 600 RPM 0.86 | Calculate the generated peak voltage. | Calculate real power of the following generator. How many pair-of-poles installed in the generator? Why does not the generator consist of one pair-of-poles only? а. b. C. d.

THydropower Plant System The following nametag is specification of a generator in a hydropower plant. MITSUBISHI AC GENERATOR Output Voltage 4. 84.5 MVA 11 kV Current Frequency Speed Power Factor 4435 A 50 Hz 600 RPM 0.86 | Calculate the generated peak voltage. | Calculate real power of the following generator. How many pair-of-poles installed in the generator? Why does not the generator consist of one pair-of-poles only? а. b. C. d.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.53P

See similar textbooks

Similar questions

For the power system of Figure Q4.1, all per unit quantities have been calculated using a common base. The generator delivers power ??∞=1 ??.??. at a lagging power factor of ????????=0.93. i) Calculate the internal voltage of the generator, the maximum electrical power that the generator can deliver to the system during the steady state operation and the steady state rotor angle, ??0, of the generator.ii)A three-phase fault occurs at busbar 3 and it is cleared by simultaneously disconnecting lines 13 and 23. Following the fault clearing, the system continues to operate with only line 12 in service. Determine the new steady state rotor angle, ??1, of the generator and the maximum power the generator can deliver to the system post fault.iii)Assuming that the post fault condition is small disturbance stable and that there is no negative interaction among system controllers, calculate the critical clearing angle, ??????, at which the fault should be cleared to ensure the generator reaches…
A Turgo type hydro-electric plant uses a 92% efficiency generator to produce its rated output of 32.5 MW. It was observed during its operation that the mechanical loss is 4.25 MW. Also, from the penstock down to the turbine, 14.3% hydraulic head loss and 8.9% leakage loss occurs which are equally distributed and based on the parameters at the dam. The average elevation from the headrace to the jet centerline is 40 m and from the tailrace to the jet centerline is 4.5 m. compute the following: a. Power by the turbine, kW b. Volume flow rate at the source, m3/s c. Power by the jet, kW d. Mechanical Efficiency, %
Discuss / Explain the operational process and show flow diagram including major equipment of a solar power plant, wind power plant, hydroelectric power plant, and biogas power plant..
DISCUSS TEH ADVANTAGES AND DISADVANTAGES OF DIFFERENT TYPES COMPESATING EQUIPMENT TO TRANSMISSION SYSTEM eXPLAIN IN DETAILS
Write factors that affecting the output power of wind turbine.
Explain briefly the advantages and disadvantages of tractor.
Suppose a power system consists of two isolated regions: a western region and an eastern region. Five units have been committed to supply 3090 MW as shown below. The two systems are separated by a transmission line that can handle a maximum transfer of 550 MW in either direction. If losses are ignored, calculate the spinning reserve for the overall system and for each region. Comment on the adequacy of the spinning reserve of the overall system, and for each region. (consider the effect on the power supply in each of the regions if the various generators fail). Repeat the above calculations and analysis if an average of 8% of the output of the generators is lost in the transmission and distribution system before reaching the load.
d. Why do we need Transmission system in various power plants and vehicles?
How does load balancing contribute to the stability and efficiency of a power distribution system? Explain.
Incremental fuel costs in dollars per megawatthour for a plant consisting of two units are given by:dC(P)/dP = 0.0080 P1 + 8.0dC(P)/dP = 0.0096 P2 + 6.4Assume that both units are operating at all times, that total load varies from 250 to 1250 MW, and that maximum and minimum loads on each unit are to be 625MW and 100MW respectively. Find the incremental fuel cost and the allocation of load between units for the minimum cost of various total loads.Write your answers in the given format below.
For the power system of Figure Q4.1, all per unit quantities have been calculated usinga common base. The generator delivers power p∞ = 1 p. u. at a lagging power factor ofcos= 0.93. i) Calculate the internal voltage of the generator, the maximum electrical powerthat the generator can deliver to the system during the steady state operationand the steady state rotor angle, σ0, of the generator.ii) A three-phase fault occurs at busbar 3 and it is cleared by simultaneouslydisconnecting lines 13 and 23. Following the fault clearing, the systemcontinues to operate with only line 12 in service. Determine the new steadystate rotor angle, σ1, of the generator and the maximum power the generatorcan deliver to the system post fault.iii) Assuming that the post fault condition is small disturbance stable and that thereis no negative interaction among system controllers, calculate the criticalclearing angle, σcr, at which the fault should be cleared to ensure the generatorreaches a new steady…
For the power system of Figure Q4.1, all per unit quantities have been calculated usinga common base. The generator delivers power p∞ = 1 p. u. at a lagging power factor ofcos= 0.93. i) Calculate the internal voltage of the generator, the maximum electrical powerthat the generator can deliver to the system during the steady state operationand the steady state rotor angle, σ0, of the generator.ii) A three-phase fault occurs at busbar 3 and it is cleared by simultaneouslydisconnecting lines 13 and 23. Following the fault clearing, the systemcontinues to operate with only line 12 in service. Determine the new steadystate rotor angle, σ1, of the generator and the maximum power the generatorcan deliver to the system post fault.