To stretch a relaxed biceps muscle 2.5 cm requires a force of 25N. Find the Young’s modulus for the muscle tissue, assuming it to bea uniform cylinder of length 0.24 m and cross-sectional area 47 cm2

To stretch a relaxed biceps muscle 2.5 cm requires a force of 25N. Find the Young’s modulus for the muscle tissue, assuming it to bea uniform cylinder of length 0.24 m and cross-sectional area 47 cm2

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 48PQ: A company is testing a new material made of recycled plastic for use in construction. Figure P14.48...

See similar textbooks

Related questions

Q: Bone or wood which has highest youngs modulus why

A: Bone has the highest young's modulus than that of wood. The value of young's modulus of bone is…

Q: end of a steel rod of radius R = 10mm and length L= 80 cm is held in a vise. A force of magnitude F…

A: Youngs modulus = mgL/πr²ΔL

Q: If the mass of the girder is 3 Mg, determine the tension developed in cables AB, BC, and BD for…

A: Find the tension in the cable AB FAB = 3000 x 9.81 = 29430 N FAB = 29.430 kN Find the tension in…

Q: The largest tendon in the body, the Achilles tendon, connects the calf muscle to the heel bone of…

Q: Find the Young’s modulus of the wire. (g= 9.81 m/s/s)

Q: The Young’s modulus for steel is at most 215 GPa (1 GPa= 109 N/m2). If you apply a force of 50.0…

A: Given quantities: Young's modulus of steel (Y) = 215 GPa Applied force (F) = 50 GPa initial length…

Q: Please I want answer of this question. Many Thanks

Q: An extremely expensive piece of spider silk is 2.5 m long and 0.5 mm in diameter is anchored to the…

Q: A tension force of 10 N is applied to a wire of cross-sectional area of 1x10 m², the wire stretched…

A: Given: A tension force, F = 103 N; Cross-sectional area, A =1×10-4 m2; The wire is stretched by 0.2%…

Q: (TUATION 3: A vertical brass post is 3.75m long and has a diameter of 25 cm. If the brass post is to…

Q: Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than o= 67874…

A: Remember that Young's modulus is given by: Y = Stress/Strain Where Stress is given by: Stress =…

Q: A 18 cm long tendon was found to stretch 5.4 mm by a force of 14.0 N. The tendon was approximately…

Q: Young's modulus of iron rod is 21 × 1010 N/m2. A force of 7.0 × 105 N is applied to a 1.5-m length…

Q: Which one of the following cannot be a definition of an elastic modulus? (A) AP -V; AV Fh B AAx FLi…

A: In the given question, We have to choose the correct option, i.e, which can not be a defination of…

Q: For safety in climbing, a mountaineer uses a nylon rope that is 65 m long and 1.4 cm in diameter.…

A: In the question given the length of rope , diameter of rope , mass and change in the length and we…

Q: A cube made of an unknown material has a dimension of 6 cm on all edges. If the upper face is…

A: A force applied tangentially to the face of a body is called shear stress (F/A). The deformation…

Q: The total tensile load of 160kN of a steel is to be stress at the middle portion limited to 150…

Q: an iron rod 4m and 0.5cm2 in cross section stretches 1mm when a mass of 225 kg is hung from it's…

Q: One end of a metal rod of radius R =8.7 mm and length L-81 cm is held in a vise, see figure. A force…

A: The expression for the Young’s modulus is,

Q: Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than o= 99260…

Q: H.W/assume a leg has 0.6m shaft of bone with an average cross sectional area of 1.5 cm.What is the…

Q: A metal wire 75.0 cm long and 0.130 cm in diameter stretches 0.0350 cm when a load of 8.00 kg is…

A: Given: Wire length, L=75 cm=0.75 m Wire diameter, D=0.13 cm=0.0013 m Elongation, ∆L=0.035 cm=0.00035…

Q: A metal rod that is 4.00m long and 0.50cm² in cross-sectional area is found to stretch 0.20cm under…

Q: Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than o= 79104…

A: maximum stress= sigma= 79104 N/m2

Q: A wire has 20 x 10^10 N/msquared young modulus. Its diameter is 1mm that can handle a tension of 0.2…

A: Given data- young modulus= 20×1010 N/m2 1mm diameter can handle a tension of 0.2 kN.

Q: A steel rod which length is (91.44cm) and the radius (1 inch), after it pulled by a (100N) force the…

Q: A 15.9 cm long tendon is found to stretch 3.81 mm when a force of 18.0 N is applied to it. If the…

A: The length of the tendon is l = 15.9 cm. The force applied on the tendon is F = 18.0 N. The average…

Q: A copper wire of length 23.179 is designed to withstand a maximum tension of 657 N and 0.627%…

A: Given Length of copper wire L = 23.179 m Tension T = 657 N Strain ∆L/L × 100 = 0.627 % ∆L/L =…

Q: A steel ring of radius r and cross-section area A is shifted on to. a wooden disc of radius R (R >>…

Q: 1.11 The homogeneous 6000-lb bar ABC is supported by a pin at C and a cable that runs from A to B…

Q: Assume Young's modulus for bone is 1.50 x 1010 N/m. The bone breaks if stress greater than 0= 80179…

A: Sigma= 80179 N/m2

Q: For safety in climbing, a mountaineer uses a nylon rope that is 50 m long and 1.0 cm in diameter.…

Q: The five-bolt connection must support an applied load of P-4700 lb. If the average shear stress in…

A: Given that - Five bolt connection Applied load(p)= 4700lb Averge shear stress in the bolt must be…

Q: For safety in climbing, a mountaineer uses a nylon rope that is 63 m long and 100-kg climber, the…

A: Given:- The length of the rope L = 63 m The diameter of the rope is d = 1.2 cm The mass of climber…

Q: A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain yy at P. Assume…

Q: When a certain liquid freezes, it expands about 10.0%. What would be the pressure increase inside an…

Q: Young's modulus of iron rod is 21 x 1010 N/m². A force of 7.0 × 105 N is applied to a 1.5-m length…

Q: A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear…

Q: Two thin rods, one made of steel and the other of aluminum, are joined end to end. Each rod is 2.0 m…

A: Given data: Length of steel and aluminium rod is L0=2.0 m Cross sectional area is A=9.1…

Q: Determine the minimum height h of the beam with a base of 8 inches if the flexural stress is not to…

A: Torque or moment of a force is given by the formula M→=r→×F→ = rperpendicular ×F Where F is the…

Q: A 10.2 m long wire with a cross-sectional area of 0.126 cm? stretches by 0.196 cm when a tensile…

A: The young's modulus of the material is a fundamental property that depends upon the temperature and…

Q: When water freezes, it expands by about 9.00%. What pressure increase would occur inside your…

Q: A metallic cube of side 125cm is subjected to a uniform force acting normal to the whole surface of…

Q: A 16.3 cm long tendon is found to stretch 2.11 mm when a force of 18.8 N is applied to it. If the…

A: Given value--- initial length = 16.3 cm. change in length = 2.11 mm. Force = 18.8 N . diameter =…

Concept explainers

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).

Question

To stretch a relaxed biceps muscle 2.5 cm requires a force of 25
N. Find the Young’s modulus for the muscle tissue, assuming it to be
a uniform cylinder of length 0.24 m and cross-sectional area 47 cm2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
Can Young’s modulus have a negative value? What about the bulk modulus?
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
Can compress stress be applied to a rubber band?
A 90-kg mountain climber bangs from a nylon rope and stretches it by 25.0 cm. If the rope was originally 30.0 m bog and its diameter is 1.0 cm, is Young’s modulus for the nylon?
In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?
Check Your Understanding A 2.0-m-long wire stretches 1.0 mm when subjected to a load. What is the tensile strain in the wire?
A steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the ceiling a 10.0-kg model aircraft that is flying in a horizontal circle with an angular speed of 6.00 rad/s. What is the strain produced in the cable?
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
What Is Static Equilibrium? Problems 13 are grouped. 1. C A ball is attached to a strong, lightweight rod (Fig. P14.1). The rod is supported by a horizontal pin near the top. The ball is at rest. Is the ball in static equilibrium? If not, why not? If so, which type of equilibrium is itstable, unstable, or neutral? Hint: What would happen if you displaced the ball slightly? FIGURE P14.1
When the structure shown below is supported at point P, it is in equilibrium. Find the magnitude .of force F and the force applied at P. the weight of the structure is negligible.