Topic: Hydraulics A volume tank 9 meters in diameter and 1.20 m high fill water 20°C in 14 minutes and 6 seconds. What is the volume flux? And the mass flux (in kilograms per second). Draw Free Body Diagram and Use 4 decimal places

Topic: Hydraulics A volume tank 9 meters in diameter and 1.20 m high fill water 20°C in 14 minutes and 6 seconds. What is the volume flux? And the mass flux (in kilograms per second). Draw Free Body Diagram and Use 4 decimal places

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter9: Mass And Mass-related Variables In Engineering

Section: Chapter Questions

Problem 40P

See similar textbooks

Related questions

Q: Instructions: Draw the three basic orthographic projections of the figure. (Top View, Front View, Ri...

A: Hand made drawing are attached herewith of different views. Which will give you idea about different...

Q: Solve for the following internal forces occurring on the beam loaded as shown below a. Moment at B i...

A: Given- Here, a= 4.1 m, b=45.6 kN/m, c= 33.4 kN , d= 13.8 kN/m Calcula...

Q: a. Axial force on member marked with a in kN. b. Axial force on member marked with b in kN.

A: Axial Force in member a is 10.2 KN

Q: Determine the factor of safety against overturning.

Q: . For the beam loaded as shown in the figure below, determine the following unknowns using a geometr...

Q: Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the a...

A: To find the absolute value of maximum shear produced

Q: 100 KN 150 KN 4.00 meters 5.00 m 4.00 meters 2.00 meters 2.00 meters Joint Horizontal Component Vert...

A: To Determine Horizontal and vertical components at A and E and Force in member Bc and BD

Q: Calculate the location Y of the center C of this gure. Calculate the primary moment (Q1) for the x' ...

A: Centroid axis: Centroid axis is any line that will pass through the centroid of the cross section. T...

Q: Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a pressure o...

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the ...

Q: A sand layer of the cross-sectional area shown in the figure has been determined to exist for a 800-...

Q: 40 kN/m 15 KN/m 600 mm GOomm 600 mm

Q: Ехample 1 A rectangular concrete beam 300 mm wide and has an effective depth of 450 mm. What is the ...

A: Design Moment Capacity: The moment capacity of a beam is the maximum bending moment that can be resi...

Q: From the figure. Determine the number of 15x20x40cm CHB required to construct the building firewall ...

Q: PROBLEM: Design a rectangular beam for a 10 m span to support a dead load of 15 kN/m (not including ...

Q: (1) The three-bar truss ABC shown in the figure is constructed of steel pipes having cross- sectiona...

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for y...

Q: An 8-meter long horizontal beam is supported to the left end by a fixed support and supported to the...

Q: Determine the discharge rate in the culvert using: (1) Darcy- Weisbach equation (f = 0.02) (2) Hazen...

Q: falling head hydraulic conductivity test is performed on a sample of soil. The standpipe. having a d...

A: Stand pipe diameter = 0.35cm Area = 0.0961cm2 Time taken = 80 sec H1 = 90cm H2 = 70 cm Length = 22...

Q: Determine the moment of inertia of the section (in mm4) about the horizontal neutral axis. All dimen...

Q: The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 880 ...

Q: View Policies Current Attempt in Progress The moment acting on the cross section of the T-beam has a...

Q: Problem 2: Determine which of the truss systems shown in a) to e) are statically determinate, static...

A: Given Data -

Q: From the given technical description shown. Lines Bearings Distances (m) AB N 32°27' E 110.8 BC ? 83...

Q: A commercial airliner with four jet engines, each producing 64 kN of forward thrust, is in a steady,...

A: The given data is: The forward thrust of each jet engine is F=64 kN Total number of thrust working=3...

Q: If a conduit of 2 m diameter is to carry a flow of 4.25 m3/s of water at 20°C (v = 1x 10^(-6) m²/s) ...

Q: An unsupported excavation is made to the maximum possible depth in a pure clay soil having density 2...

Q: P1. Two blocks A and B are released from rest at 30 degree incline when they are 50 ft. apart. The c...

Q: Determine the stress produced in rod if tensile load of 3.3 N aplied on circular cross sectional are...

A: This question is related with solid mechanics . In this question we are provided with value of tensi...

Q: 3. (a) Determine the shear force and bending moment as functions of x. (b) Draw the shear force and ...

Q: A В

Q: Question 6. Determine the support reactions and draw the axial force, shear force and bending moment...

Q: Correctly define which of the stress versus strain graphs represent the comparison of 8 ksi and 4 ks...

A: Stress- Strain curve of any material shows the material deformation caused due to applied load. Con...

Q: The W250 x 32.7 section carries a 32-kN-m bending moment inclined at 16.2° to the z-axis, as shown i...

A: step 1-

Q: civil engineering deal primarily with planning, design and construction of all the nation's construc...

A: Civil engineering is the profession of designing and constructing public-use structures such as dams...

Q: A biased dice such that any odd number is twice likely to occur for any even number is rolled once. ...

A: Given data, For biased coin an odd number is twice likely to occur for any even number is rolled onc...

Q: A confined aquifer shown has hydraulic conductivity of 52 m/day with void ratio of 0.282. The averag...

A: Distance=5.2km Void ratio=0.282 Hydraulic conductivity=52m/day

Q: Calculate for the following member forces of the frame shown below using Portal Method. a. Shear at ...

Q: Calculate the potential evapotranspiration from an area near New Delhi in the month of April by Penm...

A: Given data,

Q: Solve the specific gravity of Fluid 2 (SG2) that will make the gage pressure of Air equal to 80kPa. ...

Q: Determine the approximate axial forces, shears, and moments for all the members of the frames shown ...

Q: A symmetrical two-hinged parabolic arch rib has a span of 32 m between abutment pins at the same lev...

Q: 600 mm GOomm 600 mm 6Oomm

A: Given : Cantilever beam with diamond cross section Second moment of area at the neutral axis

Q: A confined aquifer shown has hydraulic conductivity of 52 m/day with void ratio of 0.282. The averag...

Q: The sequent depths of a hydraulic jump formed in a 4.0 m wide rectangular channel are 0.2 m and 1.0 ...

Q: A foundation carries uniform loads as shown. Determine the value of w (in kN/m). 70 kNm 円円 W (kN/m) ...

A: Given data in question Foundation Dimensions Loading ( UDL ) To find out Reaction beneath the Fo...

Q: the following are given for natural soil deposite; moist unit weight =17.8KN/m3, moisture content=1...

A: Given data: Properties of excavated soil: γ=17.8 kN/m3w=14% Properties compacted fill: γd=18.8 kN/m3...

Q: Sugarcane (root zone depth is 1.8 m) is grown in a particular area where ground water table is 2.0 m...

Q: If a two dimensional flow field is defined as V = xi - - yj then The flow is occurring along a strai...

Q: 1 Draw shear and moment diagram. Det. max. V and max. M 2. Draw loading and moment diagram given the...

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

Topic: Hydraulics

A volume tank 9 meters in diameter and 1.20 m high fill water 20°C in 14 minutes and 6 seconds. What is the volume flux? And the mass flux (in kilograms per second).

Draw Free Body Diagram and Use 4 decimal places

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Referring to Figure , how much water is stored after 20 minutes in each of the tanks? How long will it take to fill the tanks completely, provided that the volume of tank is 24 m3 and tank (a) has a volume of 36 m3 ? Assume the density of water is 1000 kg/m3 .
How much water is stored after 5 minutes in each of the tanks shown? How long will it take to fill the tanks completely provided that the volume of each tank is 12 m3 ? Assume the density of water is 1000 kg/ m3 .
Determine the specific gravity of the following gasses by comparing their densities to air at 1.23 kg/m3. Helium: 0.166 kg/m3, Oxygen: 1.33 kg/m3, Nitrogen: 1.16 kg/m3, Natural gas: 0.667 kg/m3, and Hydrogen: 0.0838 kg/m3. Answer:
Calculate the mass (kg) of a fluid having a volume of 2 m^3 and unit weight of 11.2 kN/m^3.
Determine the specific gravity of the following gasses by comparing their densities to air at 1.23 kg⁄m3 . Helium: 0.166 kg⁄m3 , oxygen: 1.33 kg⁄m3 , nitrogen: 1.16 kg⁄m3 , natural gas: 0.667 kg⁄m3 , and hydrogen: 0.0838 kg ⁄m3 .
1) 10 cu.m. OF Kerosene oil weighs 8000kg. Calculate its specific weight, density and specific gravity. 2) If an object has a mass of 45 kg. At sea level, what will be its weight at a point where the acceleration due to gravity is 9.75 m/s^2? 3) What is the value of the surface tension of a small drop of water 0.5mm in diameter which is in contact with air if the pressure within the droplet is 400Pa? 4) A reservoir of glycerin has a mass of 1,200 kg and a volume of 0.952 cu.m. determine the ff. a.) weight of glycerin b.) specific weight of glycerin c.) specific gravity of glycerin 5.) Find the capillary rise in a tube for a water glass interface (teta) = 0° if the tube radius is 1mm and the density is 1000 kg/m³. Surface tension of water is 0.0728 N/m.
The water in a tank is pressurized by air, 4 points and the pressure is measured by a multifluid manometer as shown. Determine the gage pressure of air in the tank if h1 = 0.4 m, h2 = 0.6 m, and h3 = 0.8 m. Take the densities of water, oil, and mercury to be 1000, 850 , and 13,600 kg/m^3, respectively.
Calculate the energy required to lift an elevator and its occupants with amass of 2000 kg for the following situations: (a) between the first and thesecond floor, (b) between the third and the fourth floor, (c) between the firstand the fourth floor. (as shown .) The vertical distance between eachfloor is 4.5 m. We can use as shown to analyze this problem; the energy required to lift the elevator is equal to the change in its potential energy, starting with
2.20 A water bug is suspended on the surface of the pond by surface tension ( water does not wet the legs ). The bug has six legs, and each leg is in contact with the water over a length of 7 mm. What is the maximum mass ( in grams ) of the bug if it is to avoid sinking? from Engineering fluid mechanics 11th
Measure the mass flow rate of water coming out of a drinking fountain by placing a cup under the running water and by measuring the time that it took to fill the cup. Measure the mass of the water by subtracting the total mass from the mass of the cup.
**(hydraulics)** Explain the following : 1. Explain, with the aid of an example, how the physical properties of fluids affect their behavior. 2. Do the density and specific weight change under different gravity? Explain your answer 3. What makes the density of water from different sources differ? Explain your answer. At what temperature does the water have maximum density? 4. Explain why it takes longer to cook at higher elevations. 5. Define density, specific weight, specific volume, and specific gravity. Write the relation between density and specific weight.
3. A conical tank shown in the figure has a diameter of 3 meters and an altitude of 5 meters. Find the volume of the liquid when the tank is full in cubic meters? Find volume "A" when the tank is filled to a depth of 3 meters in gallons. What is the surface area covered by volume "A" (or the wet surface area) in sauare meters?