Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively. The material has-a shear modulus of 60 kN/mm'. Determine the maximum stress in the shaft when it is subjected to a twist of 5 in a length of 2.5 m. What is the maximum torque the shaft can carry? For a circle / = nd*/32.

Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively. The material has-a shear modulus of 60 kN/mm'. Determine the maximum stress in the shaft when it is subjected to a twist of 5 in a length of 2.5 m. What is the maximum torque the shaft can carry? For a circle / = nd*/32.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.12P: A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable...

See similar textbooks

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
What torque, T, should be applied to the end of the steel shaft shown in order to produce a twist of 1.5 degrees? Use G = 80 GPa for the shear modulus.
A hollow steel shaft, 6 ft long, has an outer diameter of 3 in. and an inner diameter of 1.5 in. The shaft is transmitting 200 hp at 120 rev/min. Determine (a) themaximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106 psi for steel
Determine the outer and inner diameter (in mm) of a hollow shaft that is required to carry a bending moment of 2000 N-m and a torque of 4300 N-m if the diameter of the hole is equal to 0.7 of the outer diameter of the shaft. The shaft rotates and loads are applied suddenly, with minor shocks. The maximum bending stress is equivalent to 88 N/mm2. Apply ASME Code for this problem.
A solid circular shaft transmits 75 kW power at 200 rpm. Calculatethe diameter of the shaft and the maximum shear stress acting on it,if the twist in the shaft is not exceeding 1 º in 2 m length of the shaft.Take modulus of rigidity as 102 GPa.
Determine the minimum diameter that can be used for a solid circular steel shaft which is limited to an allowable shear stress of 70 MPa and a maximum angle of twist of 1.5o (degrees) per meter length. Applied maximum torque is 25 KN-m and the overall shaft length is 1.25 meters. Shear modulus = G= 80 GPa Note: When using torsion stress formulas, you must convert the angle of twist from degrees to radians.