Transformations (strain) Q43A strain guage rosette is placed on the outside surface of a loaded componentThe rossette has three guages aligned at 0, 45 and 90 degress.The microstrain readings are 578, 57 and 947 respectively.Use these readings to determine:the Maximium in-plane Principal Strain (Answer in microstrain).the Minimum in-plane Principal Strain (Answer in microstrain).the Principal Angle (Answer in degress).the Maximum in-plane Shear Strain (Answer in microstrain).Select the 4 correct answers from the list below/:a. 2041.83268658331b. 53.2384648095396c. 39.9288486071547Od. 46.5836567083472e. 2088.41634329165f. 1193.38076759523g. 26.6192324047698Oh. 1790.07115139285Oi. 1750.14230278569Oj. 22.6033254987178Ok. 1166.76153519046I. 2386.76153519046Om. 875.071151392846n. 7.53444183290595✓o. 1458.45191898808p. 30.1377673316238q. 33.27404050596231491.72595949404O s. 15.0688836658119✔t. 37.6722091645297

Given data εx = 578 microstrain ( at θ = 0°) εy = 947 microstrain ( at θ = 90° ) εx' = 57…

Transformations (strain) Q43 A strain guage rosette is placed on the outside surface of a loaded component The rossette has three guages aligned at 0, 45 and 90 degress. The microstrain readings are 578, 57 and 947 respectively. Use these readings to determine: the Maximium in-plane Principal Strain (Answer in microstrain). the Minimum in-plane Principal Strain (Answer in microstrain). the Principal Angle (Answer in degress). the Maximum in-plane Shear Strain (Answer in microstrain).

Transformations (strain) Q43 A strain guage rosette is placed on the outside surface of a loaded component The rossette has three guages aligned at 0, 45 and 90 degress. The microstrain readings are 578, 57 and 947 respectively. Use these readings to determine: the Maximium in-plane Principal Strain (Answer in microstrain). the Minimum in-plane Principal Strain (Answer in microstrain). the Principal Angle (Answer in degress). the Maximum in-plane Shear Strain (Answer in microstrain).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the poison ratio if longitudinal strain 0.55 lateral strain -0.33
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.4 mm and upward by v = 3.5 mm to new position Q′. Determine the shear strain γ at corner Q′ after deformation. Use c = 755 mm, α = 33°, and β = 57°.
The strain components Ex, Ey, and Yxy are given for a point in a body subjected to plane strain. Determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear strain at the point. Show the angle Op, the principal strain deformations, and the maximum in-plane shear strain distortion on a sketch. Ex = -650 UE, Ey = -345 UE, and Yxy = 1050 urad. Enter the angle such that -45°≤0p≤ +45°.
For the point given the plane stress state, which of the following is the correct type and limit values of Mohr Circle? sx =-40 MPa (Bası), sy =60 MPa (Çeki) txy =60MPa
A thin polymer plate PQR is deformed so that corner Q is displaced downward 1.3 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 64 mm, b = 100 mm, c = 80 mm, and Δ = 1.3 mm.
When an axial load is applied to the ends of the two-segment rod shown in Figure P2.1, the total elongation between joints A and C is 7.5 mm. The segment lengths are a = 1.2 m and b = 2.8 m. In segment (2), the normal strain is measured as 2,075 um/m. Determine:(a) the elongation of segment (2).(b) the normal strain in segment (1) of the rod. (Ans. to check: Normal strain (1) = 825uE
The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain. Determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear strain at the point. Show the angle θp, the principal strain deformations, and the maximum in-plane shear strain distortion on a sketch. εx = -750 με, εy = -320 με, and γxy = 1000 μrad. Enter the angle such that -45°≤θp≤ +45°.
A 100- m steel tape is used to measure the distance of the line and found to be 1,539.28m long. During measurement, the tape is supported the ends under a pull of 10kg and the observed mean temperature is 31°C. The tape is of standard temperature of 20°C and a tension of 12kg. The cross sectional area of the tape is 0.035 sq. cm. The coefficient of linear expansion is 0.0000116/°C and the modulus of elasticity of steel is 2.0 x 106 kg/ sq. cm. The tape weighs 1.5kg. a. Determine the total correction for temperature. b. Determine the total correction due to sag. c. What is the correct length of the line?
Problem 2 The solid shaft is used to transmit the torque shown. If the absolute maximum shear stress allowed in the shaft is 25.5 MPa and the maximum angle of twist in the shaft must not exceed φ= 0.025 rad, determine the value of the maximum torque T that can be appliedGiven: The shear modulus G = 75 GPa.
A uniform steel shaft has a diameter of 50 mm is fixed at ends A and B. The shear modulus of steel is 75 GPa.d) Calculate the maximum shear stress in the system in MPa. You will have to look at each individual piece of the system, so clearly indicate which segment has the maximum stress.[Ans. to check: τmax = 8.15 MPa]e) Calculate the total rotation of the shaft at point C in radians.
A rectangular block of a material with a modulus of rigidity G = 90 ksi is bonded to two rigid horizontalplates. The lower plate is fixed, while the upper plate is subject to a horizontal force P. Knowing that the upperplate moves through 0.04 in. under the action of the force, determine (a) the average shearing strain in thematerial, (b) the force P exerted on the upper plate.
The cross section of the CD part of the crane boom in the picture is a standard 50x150mm2. Determine the normal stress at the center of the part. Use exact values in the calculation, just round the answers!