Transmitted messages often include a parity bit whose value is combined with a data byte toproduce an even number of 1 bits. Suppose a message byte in the AL register contains01110101. Show how you could use the Parity flag combined with an arithmetic instructionto determine if this message byte has even or odd parity.

Transmitted messages often include a parity bit whose value is combined with a data byte toproduce an even number of 1 bits. Suppose a message byte in the AL register contains01110101. Show how you could use the Parity flag combined with an arithmetic instructionto determine if this message byte has even or odd parity.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 4VE

See similar textbooks

Similar questions

In a Von Neumann architecture, groups of bits have no intrinsic meanings by themselves. What a bit pattern represents depends entirely on how it is used. The following table shows bit patterns expressed in hexadecimal notation i. 0x000940C2 ii. 0x8C90FFFC Qa)What decimal number does each bit pattern represent if, i.It is a two’s-complement integer? ii.It is an unsigned integer? b) If each bit pattern represents an MIPS instruction, what instruction will be executed? c) What decimal number does each bit pattern represent if it is a floating-point number in IEEE 754 standard?
Write an ARM assembly program signchecks.s to assign two numbers (both positive and negative) in two variables ‘X’ and ‘Y’. In the program check the sign of the numbers using the most significant bit (MSB) (c) If both numbers have different signs, find the two’s compliment of Y and add it to X.
Assume an encoded 8-bit hamming code is stored in the memory for transmission from A to B. Using Even Parity Hamming code technique, determine the parity bits/position and the data to be stored in the memory. The 8-bit hamming code (10111011)2 is transmitted from sender A and the receiver B receives the code as (11111011)2. Draw the layout of data bits and check bits. How will the processor detect the error and correct it?
What bit addresses are set to 1 as a result of the following instructions?a. MOV 26H,#26Hb. MOV R0,#26Hc. MOV @R0,#7AHd. MOV A,#13H
Write an 8051 assembly language and 'C' Program to transfer the message "Yes" serially at 9600 baud, 8 bit data, I stop bit. Do this continuously.
In a Von Neumann architecture, groups of bits have no intrinsic meanings by themselves. What a bit pattern represents depends entirely on how it is used. The following table shows bit patterns expressed in hexadecimal notation.
) i) If CS = 020AH, SS = 0801H, SI = 0100H and IP = 1BCDH, What would be the address of the next instruction?
Create a program that reads two signed words from the input port addressed by 0xC000_00AC, adds those values, then negates the result of the addition, then subtracts 0x054 from the value before outputting the result to the output port addressed by 0xC000_0088. For this program, assume the data read from the input port is in 2’s complement format.
If you need to design a system for transmitting the output of a minicomputer to a line printer operating at a speed of 30 lines/sec over a voice grade telephone line with a bandwidth of 3 kHz. Assume that the line printer needs 16 bits of data per character and prints out 50 characters per line. What should be the minimum S/N to proceed this transmission?
The address field of a Frame Relay frame is 1011000000010111. What is the DLCI in decimal? What is the DLCI in binary? The address field of a Frame Relay frame is 101100000101001. Is this valid? Find the DLCI value if the first 3 bytes received is 7C 74 El in hexadecimal. Find the value of the 2-byte address field in hexadecimal if the DLCI is 178. Assume no congestion. How does Frame Relay differ from X.25? What is SONET and SONET/SDH? What are the various devices that can interconnect to SONET?
write an arm assembly 64 bit program IT HAS TO BE 64 BIT THE ONE ANSWERED BEFORE IS NOT 64 BIT implement a small program that parses a string stored in "my_number" into an integer (decimal number): ; "555" -> 555; ; The result should be stored in R8 ; '5' in ASCII code is represented by 0x35, the example below is "555" my_number DCD 0x00353535
Write An assembly language program to toggle the last four bits of port 2 with the time delay of 100 ms for 8051 with frequency of 16 MHz.