True or False: Dimensions can update to follow changes to your geometry.

Q: Which of the following method the forecast is done by taking average of all data.

A: We are to declare which forecasting method includes all data points

Q: For the first question I just need the explanation of neutral dwell not the steps on how to set i

A: Dwell time for ignition systems refers to the period of time that the coil is turned on. During this…

Q: Help needed in sketching thanks Several of the problems are not dimensioned. Use 5mm grid spacing…

A: Please refer the following image for the required views as per requirement.

Q: List down the procedure for analysis to find the center of gravity of an object.

A: Center of gravity of an object is defined as a point location where total mass effect appears.

Q: The given system Measured values has True value accuracy.

A: Let us discuss about accuracy from given figure.

Q: 18 бресуте пашу д slund is 1234. Determine density

A: Given data : Specific gravity=S.G Density of water=ρW   To find : Density of fluid

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK (Thin)

A: Defined the types of lines as follows. Center Lines Extension Lines Dimension Lines Cutting Plane…

Q: angular velocity and acceleration of

A: vb=ωABrAB=10*8=80in/s Now draw a velocity diagram Draw line ab perpendicular to link AB of magnitude…

Q: a.) velocity and b.) displacement.

A: Derivation for velocity and displacement.

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: Using the drawing below identify th mistake on dimensioning rules and write the correct method to…

A: According to DG&T standards, there are 5-dimensional mistakes that are highlighted in the fig…

Q: traight to the point. How far was he originally from the point, and how far did he travel in…

A: Hunter is at point A and desired to go to point P. He travelled half due east and turns 120° left.…

Q: OFFSET command use to draw object parallel to selected object by determine radius distance point…

A: Computer-aided drawing is the way to draw the various views of the component. In the orthogonal…

Q: A car has a velocity 176 ft/s. What is the velocity in MKS and CGS.

A: Given velocity of car is

Q: Angular dimensions measure the angle between. aut cad two arc Two point two objects two circle two…

A: (a) two arc: This is an incorrect option, because the angle between two arcs are not measured using…

Q: A func tion f is given. 1- cos x f(x) = Is f even, odd, or neither?

A: Given: The function is f(x) = (1-cos x)/x.   The condition for a function to be even and odd is…

Q: 5 kip/ft 15 kip ft 15 kip ft B 6 ft 10 ft 6 ft

A:

Q: calculate it manually and use your calculator to verify the manual calculation.)

A: Solution :- For part d Given :- The torque is given by the following vector product

Q: Which of the following sets of measurements can be used to calculate acceleration? *

A:

Q: Orthographic projection of the component show below

A:

Q: u- charts and c-charts are same when sample size is 1. Select one: O True O False

A: In C charts number of defect are examined at instantly.(c) But in u charts number of defects are…

Q: Known : front view , side view Req: Draw the three projections

A: Given Projection To find Front Top Side

Q: car overturned on a curve.  The center of gravity was 15 inch above ground.  The wheels were 68 inch…

A:

Q: procedure for analysis to find the center of gravity of an object.

A: Step 1 Select the reference axis. Preferably lower left corner is selected for the referance point.…

Q: Please solve in orthograpic projection multiview.

A: According to the details provided in the question, we need to DRAW three projection views.

Q: Plzz solve I give you rating

A: Given unidirectional laminate, vf=Fibre volume fraction=0.55Ef=Young's modulus of carbon fire=310…

Q: Help with dimensioning- It doesn't matter what measurement you will use. I just want to see where…

A: Concept Of Engineering Drawing Is Used

Q: 3D model with dimensions (SE or SW view) and The 3D model's Top view Note : use creo parametric to…

A:

Q: 2 kip/ft 50 kip - ft 50 kip · ft B 10 ft 20 ft 10 ft

A:

Q: le culate the values of prine

A: given:

Q: Calculate two blocks acceleration

A: For solution refer below images.

Q: Dimensions are the linear or angular sizes of a component specified on the part drawing: Group of…

A: Introduction: Engineering drawings are a subset of technical drawings. The goal is to provide all of…

Q: Name at least two units that you use every day.

A: Most of the time in the day to day life there are many duties which have to be done daily y u. Some…

Q: 'D' dimension : Basic size Tolerance Max size Min size . 'E' dimension : Max size Min size

A:

Q: Dimensions and magnitude mean size, for example the diameter of the wheels of a mountain bike etc.…

A: The dimensions help us find the size of the object. Suppose dimension of plate is given , it will…

Q: Surface plate is a marking device designed to make quicker and finer adjustments. Select one: True…

A: Surface plate: It is used in metro-logical measurement system. It is solid flat plate used as the…

Q: ship covers a distance of 24 miles in 4 hours of travel. Find the speed over ground of the vessel..…

A: This answer is given below

Q: Use CREO parametric to show the three views

A:

Q: 7. is used for measuring the wind direction.

A: To find : which instrument is used to measure the wind direction

Q: 0.Choose the correct answer. . The default option of ERASE comman Pick the objects specify radius…

A: Hi and thanks for the questions. Since you have asked multiple questions, we will solve the first…

Q: QI: Draw the orthographic Projections of given object.

A: Orthographic Projection In orthographic projection, the views of an object are projected on the…

Q: (b) Find the value of ? in factored fo 4. [3/ (x- 4)] = [(3x + 36)/ ?] 5. [4/(2x + 5)] = [? / (2x² -…

A: Hi and thank you for the questions. Since you have asked multiple questions, as per our honor code…

Q: I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal…

A:

Q: Un a trip ofd miles to another city, a truck driver's average speed was x miles per hour. On the…

A: (a) Distance between the cities = d miles, Average speed while going = x miles per hour,   Time…

Q: speed.

A: Given; A milling cutter having teeth is rotating at;  N= 135 rpmIf the tooth is, f=0.1 mmDetermine…

Q: Q3. Write a short note on: i. Aligned dimensioning. ii. Unidirectional dimensioning

A: Aligned dimensioning. A dimensioning scheme that allows all numbers, figures and notes to be aligned…