Two aluminum rods AB and BC, hinged to rigid supports are pinned together at B to carry a vertical load P = 6000 lbs. Each rod has a 0.7746 in.sq. and E = 10x10^6 psi. Both alpha and theta are 30 degrees. If the load P will change to 8000 lbs, what will be the change of the total elongation of the rod at point B in inches? Use 3 decimal point. L 10 ft B e. L= 6 ft

Two aluminum rods AB and BC, hinged to rigid supports are pinned together at B to carry a vertical load P = 6000 lbs. Each rod has a 0.7746 in.sq. and E = 10x10^6 psi. Both alpha and theta are 30 degrees. If the load P will change to 8000 lbs, what will be the change of the total elongation of the rod at point B in inches? Use 3 decimal point. L 10 ft B e. L= 6 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine thy vertical displacement (mm) of joint B. Support A is roller and support D is hinge. A=2500 mm2 E=200 GPa
In the overhanging beam show, determine P so that the moment over each support equals the moment at the midspan. W= 3.7 kN/m. Round your answer to 2 decimal places.
(G) Using these results (δ1=0.1097 in. , δ2=0.1265 in. , δ3=0.0548 in.) determine the deflections of Joint B and Point D. ANSWERS in inch (H) On a piece of paper, sketch a free body diagram (FBD) cut through rod (3) and also a FBD of the rigid bar. Using these, find a relationship between the force in rod 1 (F1) and the applied load, P, a relationship between the force in rod 2 (F2) and the applied load, P, and also a relationship between the force in rod 3 (F3) and the applied load, P. (I) Based on the allowable stress for the bronze, calculate the maximum allowable force that can be supported by rod (1), and the corresponding maximum value for the applied load P. IN KIPS (J) Based on the allowable stress for the aluminum, calculate the maximum allowable force that can be supported by rod (2) and rod 3, and the corresponding maximum value for the applied load P. IN KIPS (K) Using the results from Part 8, determine the deflections of Joint B and Point D. IN INCH NOTE: These are the…
you did not use the correct value, a=5m and b= 2m, also, the force is q =5.1kn/m and not 5.3 kn/m can you do it with the right value please, or explain step by step without wrong value
Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
# = poundsa) what is the shear force at 5' rt. of A? (in pounds, 2 decimal places)b) what is the bending moment at 5' rt. of A? (in pounds, 2 decimal places)
The 300-lb force is to be resolved into components along lines a-a’ and b-b’. 1. Determine the angle α knowing that the component along line a-a’ is 240-lb. 2. What is the corresponding value of force along line b-b’?
The flexural rigidity, EI, is constant from point A to point D. Use point A as the origin for the x and y axes. Always use 3 decimal place in your final answer if it is not whole number. (Macaulay's Method)What is the slope at point A? in terms of 1/EIWhat is the deflection at point B? in terms of 1/EIWhat is the deflection at point C? in terms of 1/EIWhat is the reaction at the hinge support A? in kN (use 3 decimal places)What is the slope at point D? in terms of 1/EIWhat is the reaction at the roller support D? in kN (use 3 decimal places)
Solve a part only in 20 min and take a thumb up plz
What is the internal force in member AD? A. 750 N , T B. 450 N , T C. 750 N , C D. 450 N , C SHOW SOLUTIONS
draw the digram and calculate the forces
.15 2.16 The three forces acting on the beam can be replaced with a single equivalent force R. Determine the angle θ and R. 25kN P2 60 kN P3 80 kN 40° 50° 4 m 6 Figure P2.16 COMPANY