Two batteries A and B are2.connected in parallel and load of 10 Qis connectedacross their terminals. A has an e.m.f. of 12 V and aninternal resistance of 2 Q ; B has an e.m.f. of 8 V andan internal resistance of 1 Q Use Kirchhoff's laws todetermine the values and directions of the currentsflowing in each of the batteries and in the externalresistance. Also determine the potential differenceacross the external resistance,Two resistors of values 1 kQ and 4 Q are connected in series across a constant3.voltage supply of 100 V. A voltmeter having an internal resistance of 12 kQ is connected across the4 k2 resistor. Draw the circuit and calculate(a) true voltage across 4 k£2 resistor before the voltmeter was connected.(b) actual voltage across 4k2resistor after the voltmeter is connected and the voltage recordedby the voltmeter.(c) change in supply current when voltmeter is con-nected.(d) percentage error in voltage across 4 kN resistor.

We are authorized to answer one question at a time, since you have not mentioned which question you…

Two batteries A and B are connected in parallel and load of 10 Qis connected across their terminals. A has an e.m.f. of 12 V and an internal resistance of 2 Q; B has an e.m.f. of 8 V and an internal resistance of 1 2 Use Kirchhoff's laws to determine the values and directions of the currents flowing in each of the batteries and in the external resistance. Also determine the potential difference 2. across the external resistance.

Two batteries A and B are connected in parallel and load of 10 Qis connected across their terminals. A has an e.m.f. of 12 V and an internal resistance of 2 Q; B has an e.m.f. of 8 V and an internal resistance of 1 2 Use Kirchhoff's laws to determine the values and directions of the currents flowing in each of the batteries and in the external resistance. Also determine the potential difference 2. across the external resistance.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

To determine the value of the resistances of the lightbulbs, look for the POWER (watt) and VOLTAGE DROP (V=220V) on the label of your lightbulbs. Then, use the derived formula of power (R = V2 / P) to get the resistance of each lightbulb.After getting the resistance of each lightbulb, compute the total and individual values of the resistance, current, and voltage using the process of solving resistors in circuit following the GAFSA (Given, Asked, Formula, Solution, and Answer) format.Given:VT = 220VP1 = 2.5wP2 = 2.5wP3 = 2.5wP4 = 10wP5 = 5wP6 = 5wP7 = 5wP8 = 10wP9 = 6wP10 = 6w
following equation applies: V = IR. Outside of the linear range, V*IR, outside of the linear ranges where resistors are broken The resistor has a resistance of 100ohm, and a power rating of 250mW. 1) Sketch the plot (and label) of the i-v relationship for the resistor using only the linear range of the resistor. Determine the range of values for the voltage and current that the resistor operates as a linear element and note these simplified numerical values on the plot.
In the circuit of Fig.2, the current through R3 is 10% of the load current supplied through its terminal. The resistances R1, R2 and R3 can be determined when the voltage and current in each resistance had been determined. Determine the following: a. The total resistance of the circuit is? b. The total current is? c. The power dissipation of R2 is?
1. a) Find an expression for the equivalent resistance of two resistorsof value R in series.2. b) Find an expression for the equivalent resistance of n resistors ofvalue R in series.3. c) Using the results of (a), design a resistive network with anequivalent resistance of 3 kΩ using two resistors with the samevalue from Appendix H.4. d) Using the results of (b), design a resistive network with anequivalent resistance of 4 kΩ using a minimum number of identicalresistors from Appendix H.
When electricity is transported from a power station to a city, the line voltage (relative to ground) is usually on the order of several hundred thousand volts. A power line cable has a radius of a = 2.0 cm, is made of aluminum with a resistivity of ρ = 2.7×10−8 Ω ⋅ m, and spans a distance of l = 100 km from a power station to a city. The city consumes 100 MW of power (so I2RL =100MW). (a) Find the resistance of the power cable between the station and the city(i.e.,between points A and B). (b) Suppose that the line voltage ∆VBC = 120 V. i. How much current is required to flow through the power line to deliver 100MW of power to the city? ii. How much energy is lost as heat between points A and B? (c) Suppose that the line voltage ∆VBC = 300 kV. i. How much current is required to flow through the power line to deliver 100MW of power to the city? ii. How much energy is lost as heat between points A and B?
In a design task, a wire of 2000 m requires to exhibit a voltage drop of 2.5 Vwhen 3.2 A of current passes though it. Based on the Table Q1 (b) below, inyour opinion, which of the wire is the most suitable for aviation when the fuelsaving is another factor to be considered as well.
a) The power, P, consumed by a resistor of resistance R, is given by P = E^2R Given that E = 20 V and R = 1000ꭥ, using partial derivatives, find the approximate change inpower if E is decreased by 0.5 V and R is increased by 50ꭥ.b) Check and compare your findings using standard electrical principles.
An aluminum wire 7.5m long is connected in parallel with a copper wire 6m long. When a current of 5A is passed through the combination, it is found that the current in the aluminum wire is 3A. If the diameter of the aluminum wire is 1mm, determine the diameter of the copper wire. Assume the resistivity of copper to be 0.017µΩm and that of aluminum to be 0.028 µΩm. Major Topic 7 Factors that affect the resistance
ADVANCED PHYSICS (THUMBS UP WILL BE GIVEN. PLEASE CHOOSE THE CORRECT ANSWER. NO LONG EXPLANATION NEEDED.) Consider the circuit shown below. The cross-sectional areas of the battery, the wire, and the bulb filament are 10.0 cm2, 5.00 mm2 and 0.200 mm2 respectively. Which of the following statements is/are TRUE? I. The current density in the battery is greater than that in the bulb filament.II. The current densities in the battery, in the wire, and in the bulb filament are equal.III. The currents in the battery, in the wire, and in the bulb filament are equal. choices: a. I and III only b. II only c. II and III only d. I only e. III only
For the three-way bulb (50 W, 100 W, 150 W) discussed in Conceptual Example 11, find the resistance of (a) the 100-W filament and (b) the 50-W filament. Assume that the wattage ratings are not limited by significant figures and ignore any heating effects on the resistances.
A power plant produces 1000MW to supply a city 40km away. Current flows from the power plant on a single wire with resistance through the city and returns via the ground, with negligible resistance. At the power plant the voltage between wire and ground is 115 kV. Determine: (a) the current in the wire, and (b) the fraction of the power lost in transmission.
4. The heating element in an oven has a resistance of R =32 ohms. One of thewires connecting the oven to the 220 volt power source is loose, contributingan additional r = 5 ohms to the closed-loop circuit. What is the power Povenradiated in the oven, and what is the rate Pcontact at which heat is dissipatedat the loose contact? The looser is the connection, the greater is the resistance r: What value of r is most likely to cause a fire. Also agraph showing Pcontact versus r