Two different loads A and B are connected across a balanced 230 V. 3-phase lines. Load A is a three-phase load that draws 10 kVA at 70% lagging pf. Load B is a single- phase load connected across lines a and b drawing 5 kVA at unity pf. Determine line current in line a. Assume a phase sequence of a-b-c. (Hint: Assume the three phase load is delta connected)

Two different loads A and B are connected across a balanced 230 V. 3-phase lines. Load A is a three-phase load that draws 10 kVA at 70% lagging pf. Load B is a single- phase load connected across lines a and b drawing 5 kVA at unity pf. Determine line current in line a. Assume a phase sequence of a-b-c. (Hint: Assume the three phase load is delta connected)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.44P: Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a...

See similar textbooks

Similar questions

Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line currents as well as the neutral current are always zero. (a) True (b) False
Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at 0.9 power factor leading, are connected in parallel and supplied by a balanced three-phase Y-connected, 480-V source. (a) Determine the source current. (b) If the load neutrals are connected to the source neutral by a zero-ohm neutral wire through an ammeter, what will the ammeter read?
Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a series impedance of (0.4j2.7) per phase. One of the loads absorbs 560 kVA at 0.707 power factor lagging, and the other 132 kW at unity power factor. The line-to-line voltage at the load end of the line is 2203V. Compute (a) the line-to-line voltage at the source end of the line. (b) the total real and reactive power losses in the three-phase line, and (c) the total three-phase real and reactive power supplied at the sending end of the line. Check that the total three-phase complex power delivered by the source equals the total three-phase comp lex power absorbed by the line and loads.
In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the line-to-neutral voltages are always equal to zero. (a) False (b) True
It is stated that (i) balanced three-phase circuits can be solved in per unit on a per-phase basis after converting - load impedances to equivalent Y impedances. (ii) Base values can be selected either on a per-phase basis or on a three-phase basis. (a) Both statements are true. (b) Neither is true. (c) Only one of the above is true.
A single-phase source is applied to a two-terminal, passive circuit with equivalent impedance Z=3.045, measured from the terminals. The source current is i(t)=22cos(t)kA. Determine the (a) instantaneous power, (b) real power, (c) reactive power delivered by the source, and (d) source power factor.
Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
Three identical impedances Z=3030 are connected in to a balanced three-phase 208-V source by three identical line conductors with impedance ZL=(0.8+j0.6) per line. (a) Calculate the line-to-line voltage at the load terminals. (b) Repeat part (a) when a s-connected capacitor bank with reactance (j60) per phase is connected in parallel with the load.
Does an open connection permit balanced three-phase operation? - (a) Yes (b) No
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
A Factory is supplied froma 3-phase, 4-wire, 400 V, simmetrical system. The resistance of each line is 0.4 Ωand of the neutral 0.6 Ω. The power input to the main is as follows: 10 KVA at a laggin poer factor ofd 0.7 to phase R, 10 KVA at a leading power factor of 0.7 to phase S, and 10 KVA at unity power factor to phase T. Calculate the current in the neutral wire and the voltaje between line R and the neutral at the Factory. Phase secuence RST.