Two engineers have a disagreement over the selection of transmission line for connections within a 100m Data Centre on a project that is at risk for cost overrun. The first engineer is arguing in favor of using multi-mode fibre while the second engineer would like to use single mode fibre. You are the project engineer. Decide which of the two transmission lines to use and justify your answer.

Two engineers have a disagreement over the selection of transmission line for connections within a 100m Data Centre on a project that is at risk for cost overrun. The first engineer is arguing in favor of using multi-mode fibre while the second engineer would like to use single mode fibre. You are the project engineer. Decide which of the two transmission lines to use and justify your answer.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.5MCQ

See similar textbooks

Similar questions

Consider the bandwidth of the line is 1.2 Mbps, packet size is 1 KB and round-trip time is 50 msec. What is the link utilization in stop and wait? a) 10.8% b) 14% c) 12% d)13.5%
A. Given a fixed route and fixed link types between two end systems, which of the following delays may vary depending on the level of congestion in the network? Select one: a. processing delay b. propagation delay c. transmission delay d. queueing delay ============================= B. Suppose there is exactly one packet switch between a sending host and a receiving host. The transmission rates between the sending host and the switch and between the switch and the receiving host are R1 and R2, respectively. Assuming that the switch uses store-and-forward packet switching, what is the total end-to-end delay to send a packet of length L? (ignore queuing, propagation, and processing delays) Select one: a. L/(R1+R2) b. (R1+R2)/L c. L/R1+L/R2 d. 2∗(L/R1)
Explain the concept of modulation in wireless transmission technology and its significance in data transmission.
Explain the concept of modulation in wireless transmission technology.
Give four challenges and suggest solutions for those challenges in wireline operations.
URGENT: Which of the following is not a characteristic of fiber cable? Low cost Throughput Noise immunity Size
What is the difference between power gain and insertion loss in two-port networks?
a) i. Distinguish between circuit and packet switching in communication system. a) ii. State two advantages and disadvantages of a circuit switching technique. a) iiiHow are messages or data in a packet switching techniques are routed to their destination. b) i. What are the modes of propagation in transmission system? b) ii. With the aid of sketch discuss one of the modes. What are the diversity techniques available in transmission network and discuss any two?
With the system shown in the figure, use 100MVA as system base, and 230 kV as base voltage along the transmission line. For the same system in the figure, build the Y-bus matrix without the Load. 1. What is the element Y11? Provide the susceptance value 2. What is the element Y22? Provide the susceptance value
Do not use chatgpt What is transmission line?
Briefly explain which factors are important for planning a Wireless LAN design for a campus network.
A.a.Two electricians are discussing industrial cabling. Electrician A says that copper cable provides clearer transmission signals than fiber optic cable. Electrician B says that fiber optic cables will be larger thancopper cables with identical data transmission rates. Who is correct?B. Both Electrician A and Electrician B are correct.C. Only Electrician A is correct.D. Neither Electrician A nor Electrician B is correct. A.b. Two electricians are discussing industrial cabling. Electrician A says that signal losses in fiber optic cableare more likely to be caused by splices and connectors than cable length. Electrician B says that wire-wrapterminations should be used when there isn't enough time available to use IDC terminations. Who iscorrect?A. Only Electrician A is correct.B. Both Electrician A and Electrician B are correct.C. Only Electrician B is correct.