Two forces act on the hook. (Figure 1) Figure 1 of 1 40° 30° F₁ Part A Determine the magnitude of the resultant force, if F₁ = 220 N, F₂ = 530 N. Express your answer to three significant figures and include the appropriate units. FR = Submit μА Value Units My Answers Give Up ? Provide Feedback Continue

Two forces act on the hook. (Figure 1) Figure 1 of 1 40° 30° F₁ Part A Determine the magnitude of the resultant force, if F₁ = 220 N, F₂ = 530 N. Express your answer to three significant figures and include the appropriate units. FR = Submit μА Value Units My Answers Give Up ? Provide Feedback Continue

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A manipulator’s end-effector position is calculated as follows:x = q0 cos q1 + l2 cos(q1 + q2),y = q0 sin q1 + l2 sin(q1 + q2),where q0,1,2 represent joint displacements and l2 is a constant positive parameter.Which of the following describes this manipulator:1) This is a robot-manipulator with 3 revolute joints.2) This is a robot-manipulator with 2 revolute and 1 prismatic joints.3) This is a robot-manipulator with 1 prismatic and 3 revolute joints.4) This is a robot-manipulator with 2 revolute joints. A robot’s end-effector’s tool position is defined asx = L1 cos(q1) + q3 sin(q1 + q2)where L1 = const, q1 = q1(t), q2 = q2(t) and q3 = q3(t) with t defining time. Calculate ∂x / ∂q3 1) it is impossible to calculate as the equation for the y and z positions are missing.2) cos(q1 + q2).3) it is impossible to calculate as time is not given.4) sin(q1 + q2).
A device with a mass of 1000 kg is placed on top of the suspension, whereby the springs are compressed into a pile a distance of 4 mm. What is the system specific angle frequency (rad / s) to one decimal place?
1. The equation of motion for a vibrating system with viscous damping isd2x/dt2 + c/m X dx/dt + s/m X x = 0If the roots of this equation are real, then the system will bea) over dampedb) under dampedc) critically dampedd) none of the mentioned
a string is attached to a mechanical vibrator, which has a frequency of 30Hx. the sttring is 3.0m long and has a linear density of .4 g/cm. the tension is varied by adding weights to teh string passing over the pully. What tension is needed to cause the string to resonate with the vibrator in four segments. assume that he points where the string meets the vibrator and the pulley are approx nodes.
2- I need answer of all sub-parts questions. Thanks The figure shows a simple model of a motor vehicle that can vibrate in the vertical direction while traveling over a rough road. The road surface varies sinusoidally with an amplitude of 0.01 m and a wavelength of 6 m. The vehicle has a mass of 1007 kg. The suspension system has a total spring constant of 40 kN/m and a damping coefficient of 20 kN.s/m. The vehicle average speed is v = 100 km/hr. The objective is to determine the vehicle steady-state displacement amplitude as well as the respective transmitted force. Calculate the resultant frequency ratio of the above model. Calculate the steady state amplitude of the vehicle. Determine the force amplitude that will be felt in the vehicle at the steady-state due to the bumpiness of the road.
1- I need answer of all sub-parts questions. Thanks The figure shows a simple model of a motor vehicle that can vibrate in the vertical direction while traveling over a rough road. The road surface varies sinusoidally with an amplitude of 0.01 m and a wavelength of 6 m. The vehicle has a mass of 1007 kg. The suspension system has a total spring constant of 40 kN/m and a damping coefficient of 20 kN.s/m. The vehicle average speed is v = 100 km/hr. The objective is to determine the vehicle steady-state displacement amplitude as well as the respective transmitted force. Calculate the forcing frequency of the pumpy road. Calculate the natural frequency of the vehicle SDOF system. Calculate the damping ratio of the vehicle SDOF.
A block with a speaker bolted to it is connected to a spring having spring constant k=20.0N/m as in figure P17.40 The total mass of the block and speaker is 5.00lg and the amplituted if this unit's motion is 0.500m. a) If the speaker emits sound waves of frequency 440Hz, determine the highest and lowest frequencies heard by the person to the right of the speaker b) If the maximum sound level heard by the person is 60.0 dB when he is closed to the speaker, 1.00m away, what is the minimum sound level heard by the observer? Assume that the speed of sound is 343m/s
Vibrations Question The governing equation of motion of a single degree–of–freedom (SDOF) system is given by 5xdoubledot(t)+20xdot(t)+1800x(t)=10cos(15t)+30sin(5t)(assume the units are Newtons) and the initial conditions of the system are given asx(0)=0.02m and v(0)=0.95m/sAnalytically obtain the total response of the system
Obtain the steady-state difference (f(∞) - v(∞) between the input and output of the following model: Tv + v= bf(t), where b is a constant and f(t) = mt. Assume that v(0) = 0 and that the model is stable (T > 0).
Discussion: 1- Measuring the angle of phase shift for every state. set the AC voltage source 15V and using the data in the following table NO. Frequency | Capacitance | Resistance | Inductance 1 2KHZ 0.1uF 100Q 0.1mH 2 20 KHZ 0.1 yF 100 Q 0.1 mH 3 200 KHZ |0.1 pF 100 Q 0.1 mH 2- Draw the phase shift for every state as graph .
Vibrations Question The governing equation of motion for a base motion system is given by (assume the units are Newton) mx''(t)+ cx'(t)+kx(t)=cYwbCos(wb*t)+kYSin(wb*t)Given that m = 180 kg, c = 30 kg/s, Y = 0.02 m, and wb= 3.5 rad/s Find the largest value of the stiffness, k that makes the transmissibility ratio less than 0.85
The response of a system is given by xt=0.003cos 30t +0.004sin 30t m. Determine (a) the amplitude of motion, (b) the period of motion, (c) the frequency in Hz, (d) the frequency in rad/s, (e) the frequency in rpm, (f) the phase angle, and (g) the response in the form of xt=Asin (ωt+φ)