Two identical rods AB and CD each have a length Z and diameter d, and are used to support the rigid beam, which is pinned at E A vertical force P is applied to the beam as shown in (Figure 1). The rods are made of material that has a modulus of elasticity of E Figure - Part A Determine the angle of rotation of the beam Express your answer in terms of some, all, or none of the variables P, a, E, d. L. and the constant. 1.5PL nad Submit D ΑΣΦ IT vec 4 Previous Answers Request Answer X Incorrect Try Again: 3 attempts remaining ? 10/1

Two identical rods AB and CD each have a length Z and diameter d, and are used to support the rigid beam, which is pinned at E A vertical force P is applied to the beam as shown in (Figure 1). The rods are made of material that has a modulus of elasticity of E Figure - Part A Determine the angle of rotation of the beam Express your answer in terms of some, all, or none of the variables P, a, E, d. L. and the constant. 1.5PL nad Submit D ΑΣΦ IT vec 4 Previous Answers Request Answer X Incorrect Try Again: 3 attempts remaining ? 10/1

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.12.4P

See similar textbooks

Similar questions

A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
Five bars, each having a diameter of 10 mm. support a load P as shown in the figure. Determine the plastic load Ppif the material is clastoplastic with yield stress
A steel rod of 30 mm diameter is enclosed centrally in a hollow copper tube of external diameter 40 mm and 5 mm thick. The composite bar is then subjected to an axial pull of 45 kN. If the length of the compound rod is 150 mm , and the elasticity moduli are Est = 200 GPa and Ecu = 100 GPa , determine: 1.2.2 The load carried by the rod and that carried by the tube
A straight and piecewise uniform bar ABCD of total length L is in Case 1 fixed at A in case 1 and in Case 2 fixed at both ends A and D. AB = BC = CD = L/3. The cross section area of segment CD is half of the area of the segment ABC, i.e. AABC = 2ACB. A point load of P is applied at B. Assume that bar material is linear and elastic and the modulus of elasticity is E.
A steel [E = 25500 ksi] pipe column (1) with a cross-sectional area of A1 = 5.60 in.2 is connected at flange B to an aluminum alloy [E = 17500 ksi] pipe (2) with a cross-sectional area of A2 = 4.40 in.2. The assembly is connected to rigid supports at A and C. For the loading shown, determine the normal force in the steel pipe (1).
A straight and piecewise uniform bar ABCD of total length L is in Case 1 fixed at A in case 1 and in Case 2 fixed at both ends A and D. AB = BC = CD = L/3. The cross section area of segment CD is half of the area of the segment ABC, i.e. AABC = ACB. A point load of P is applied at B. Assume that bar material is linear and elastic and the modulus of elasticity is E.
A light ridig member AB is pinned at A and is further supported by light elastic rods CD and GF, member AB supports a 5000lb load at B the elastic modulus for the two elastic rods CD and GF is given as E= 30x106 psi and the cross-sectional area for each of these rods is 1 in2. what are the forces in the two supporting elastic rods as a results of the loading?
Two members AB and AC are made of material with E= 138 Gpa and each member has cross sectional area of A= 346 mm2. The members are used to support bar BC. If P=1917 N, L1= 242 mm , L2= 373 mm and L3= 459 mm . Answer the following questions. The tension in member AB? The tension in member CD? The elongation in member AB? The elongation in member CD? Vertical displacement of point E?
A straight bar 450 mm long is 10 mm in diameter for the first 200 mm length and 20 mm in diameter for the remaining length. If the bar is subjected to an axial push of 10 kN, determine decrease in length of the bar. Take modulus of elasticity of bar material E = 2 × 105 N/mm²
a) Determine the tensile force T’ in the rope on the side connected to joint B: b) Determine the internal compressive normal force ƒBC in the tube BC: c) Determine the horizontal reaction force Rx and the vertical reaction force Ry in joint A: d) Determine the moment M of the center of bar AB: e) Determine the compressive stress σBC in the tube BC: f) Determine the critical load Pc for the tube BC: g) Which of the following statements about the tube BC is correct: A. The tube BC fails due to yielding B. The tube BC fails due to buckling C. The tube BC fails due to both yielding and buckling D. The tube BC is safe against both yielding and buckling h) Pin C has a diameter of 30 mm; calculate the shear stress τ of the pin C, when considering one cross-section for shear stress calculation: