Two masses A and B are 5kg and 2kg respectively rotating in a shaft. The corresponding radii of rotation are 0.2m and 0.3m respectively and the angle between the masses is 600. Find the position and magnitude of the balance mass required, if its radius of rotation is 200 mm using graphical method and also verify your answer with analytical method.

Two masses A and B are 5kg and 2kg respectively rotating in a shaft. The corresponding radii of rotation are 0.2m and 0.3m respectively and the angle between the masses is 600. Find the position and magnitude of the balance mass required, if its radius of rotation is 200 mm using graphical method and also verify your answer with analytical method.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.39P: The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables...

See similar textbooks

Similar questions

In Sample Problem 5.5, determine Oy with one scalar equilibrium equation.
The uniform 240-lb bar AB is held in the position shown by the cable AC. Compute the tension in the cable.
The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
A vertical bar of length L with mass of 40 kg is rotated vertically about its one end at 40 rpm. Find the length of the bar if it makes and angle of 45° with the vertical.
Suppose a 30 lb truck wheel 18 in. in diameter has a radius of gyration of 4 in. and the 6120 lb truck’s weight is distributed equally to each of the four wheels.a. If the truck can supply 150 lb x ft of torque to each wheel, how fast would the wheel want to accelerate if it didn’t slip? b. What would the coefficient of friction have to be in order to keep the wheel from slipping
The rope shown in the figure below is wound around a cylinder of mass 4.0 kg and I = 0.020 kg m2, about the cylinder axis. If the cylinder rolls without slipping, what is the linear acceleration of its center of mass? What is the frictional force? Use an axis along the cylinder axis for your computation. What happens if the frictional force between table and cylinder is negligible? Choose any axis for your computation.
The shaft, bearing two unbalanced masses, rotates at a constant speed of ω = 20 r/s. In the case of balancing in the DI and DII planes, find the balancing values (kg.mm) and their positions.
A turntable is a uniform disc of mass 2 kg and radius 1.3 x 10-1 m. The turntable is spinning at a constant rate of = 0.5 . The motor is turned off and the turntable slows to a stop in 8.0 s with constant angular deceleration. Find the (a) moment of inertia of the turntable; (b) initial rotational kinetic energy; (c) angular deceleration of the turntable while it is slowing down; (d) total angle in radians that the turntable spins while slowing down; and (e) magnitude of the frictional torque.
A weight of 500 kg is being lifted up at a uniform speed of 1.5 m/s by a winch driven by a motor running at a speed of 1000 rpm. The moments of inertia of the motor and winch are 0.3 and 0.3 kg-m respectively. In the absence of the weight, the motor develops a torque of 100 Nm at a speed of 1000 r/min. Calculate the motor torque and the equivalent moment of inertia referred to the motor shaft
A crane that is 10 meters long is rotating (while loaded), at 1 radians/sec. It is stopped instantly (in 0.1 radian) in the position shown. Due to momentum the load continues to swing. Ignoring the deflection of the crane for this problem. (list all assumptions). The load is 750 lbs. a) The weight of the 10 m crane boom is 3000 lb and the mass moment of inertia is 80 lb ft s^2 about the centroid. Using the parallel axis theory find the mass moment of inertia around the point of rotation. b) What forces and moments are there on the boom at the point of rotation?
Four masses m1, m2, m3 and m4 are 100 kg, 200 kg, 140 kg and 160 kg respectively. The corresponding radii of rotation are 0.2 m, 0.15 m, 0.25 m and 0.3 m respectively and the angles between successive masses are 30°, 75° and 100°. Find the position and magnitude of the balance mass required, graphically, if its radius of rotation is 0.2 m.