Two metal bars are fastened together at the bolted flange connection shown. There are 2 total bolts connecting the two metal bars together and each bolt has diameter dbolt 0 12.7 mm. The flange is oriented at angle = 50° with respect to longitudinal axis of the metal bars. If an axial force F = 30 kN is applied as shown, determine the overall safety factor of the bolted connection. You may assume the bolts are made out of 1020HR steel and the strength of the bolt in shear is 50% of the tensile strength of the bolt material. -

Two metal bars are fastened together at the bolted flange connection shown. There are 2 total bolts connecting the two metal bars together and each bolt has diameter dbolt 0 12.7 mm. The flange is oriented at angle = 50° with respect to longitudinal axis of the metal bars. If an axial force F = 30 kN is applied as shown, determine the overall safety factor of the bolted connection. You may assume the bolts are made out of 1020HR steel and the strength of the bolt in shear is 50% of the tensile strength of the bolt material. -

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.8.1P: The shear stresses t in a rectangular beam arc given by Eq. (5-43): in which Fis the shear force, /...

See similar textbooks

Similar questions

An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is w = 70 mm and the bar thickness is 20 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 130 MPa, the bearing stress in the bar cannot exceed 140 MPa, and the bearing stress in the bracket cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The five bolt connection must support an applied load of P = 2000 lb. If the average shear stress in the bolts must be limited to 32 ksi, determine the minimum bolt diameter that may be used for this connection.
The five-bolt connection must support an applied load of P = 1800 lb. If the average shear stress in the bolts must be limited to 47 ksi, determine the minimum bolt diameter that may be used for this connection.
A flange coupling connects two shafts in order to transmit 250 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm located at a 210 mm bolt circle diameter. Determine the flange thickness if the bearing stress on the flange is 95 MPa. A. 10 mm B. 20 mm C. 25 mm D. 30 mm
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
(6) A key is to be designed for a 12.7cm shaft which will transmit power of 150kW @ 360 rpm. If the allowable compressive stress is 1,200kg/cm2, determine: (a) cross-sectional dimensions of the square key to be used; (b) length of the key.
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 12 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 135 MPa. Determine the maximum value of Pmax that can be supported by the structure.
A stepped circular bar having diameter 20 mm, 15 mm and 10 mm over axial lengths of 100 mm, 80 mm and 60 mm, respectively, is subjected to an axial tensile force of 5 kN.If E = 100×103 N/mm2and Poisson’s ratio v = 1/m = 0.32 for the material of the bar, determine a) Total change in length.b) Change in each diameter.
A bar made of A-36 steel has the dimensions shown below. If an axial force of P = 64 kN is applied to the bar. Use E = 200 GPa for A-36 steel. Determine the change in its length: ______ µm.
Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 53 kN if it developed a stress of 52 MPa. Take note that the inner diameter is 2/6 of the outer diameter. Hiiii i am having a hard time. It is kinda urgent tysm i appreciate u sm
A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the limiting stress of the bar is 27.24 kPa determine the cross sectional area of the steel square bar and its dimensions.