Two metal bars are fastened together at the bolted flange connection shown. There are 4 total bolts connecting the two metal bars together and each bolt has diameter dbolt 12.7 mm. The flange is oriented at angle = 50° with respect to longitudinal axis of the metal bars. If an axial force F = 40 kN is applied as shown, determine the overall safety factor of the bolted connection. You may assume the bolts are made out of 1020HR steel and the strength of the bolt in shear is 50% of the tensile strength of the bolt material. F D Ө F

Two metal bars are fastened together at the bolted flange connection shown. There are 4 total bolts connecting the two metal bars together and each bolt has diameter dbolt 12.7 mm. The flange is oriented at angle = 50° with respect to longitudinal axis of the metal bars. If an axial force F = 40 kN is applied as shown, determine the overall safety factor of the bolted connection. You may assume the bolts are made out of 1020HR steel and the strength of the bolt in shear is 50% of the tensile strength of the bolt material. F D Ө F

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.55P: Solve Prob. 10.54 assuming that A and B are connected by a spring of stiffness k = 0.3 W/b and free...

See similar textbooks

Similar questions

As shown below, the hydraulic cylinder at C is used to pull a bar from a pump, which is connected to a support ABC at A. The critical elements are the diameter dr of the bar and the diameter dp of the pin at B. For a factor of safety FS = 3.0, determine the required diameters if the maximum load on the bar suction for Pa = 15 kN. The failure voltages of the bar and pin are σe = 340 MPa and τe = 400 MPa, respectively.
A small stepladder has vertical rails and horizontal steps formed from a C-section aluminum channel. Two rivets, one in front and one in back, secure the ends of each step. The rivets attach the steps to the left and right hand rails. A 225 lb person stands in the center of a step. If rivets are formed of 6061-T6 aluminum, what should be the diameter d of the rivets? Use a factor of safety of 8 and round your answer to the nearest 1/16 of an in.
A steel column is of length 8m and diameter 600 mm with both ends hinged.Determine the crippling load by Euler’s formula. Take 5 E = 2.1x10 N/mm2
Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and made of aluminum that has anelastic modulus of E = 12,000 ksi. Determine the maximum magnitude of load P that can be applied to the rigid bar withoutcausing member (1) to buckle
Q#3. An aluminium strut 16 ft long has a rectangular cross section 2 in by 3.5 in. A bolt through each end secure the strut in such a way that is acts as hinged column about an axis perpendicular to 3.5 in dimension; and as fixed column about an axis perpendicular to 2 in dimension. Determine the safe central load with a factor of safety of 2 and E= 10300000 psi. Also discuss in detail about the governing column capacity and reasons behind it.
An aluminum strut 2.50m long has a rectangular section 60mm by 30mm. A bolt through each end secures the strut so that it acts as a hinged column about an axis perpendicular to the 60 mm dimension and as a fixed ended column about an axis perpendicular to the 30mm dimension. Determine the safe central load using a factor of safety of 2.5 and E = 70 Gpa.
The stress–strain diagram for a material can be approximated by the two line segments shown. If a bar having a diameter of 80 mm and a length of 1.5 m is made from this material, determine the critical load provided one end is pinned and the other is fixed. Assume that the load acts through the axis of the bar. Use Engesser’s equation.
The 2500 N light fixture used in sports gymnasiums is supported by three rods interconnected by an A-ring. Determine the smallest diameters of rods AB, AC and AD, knowing that the limiting voltage of AB is 480Mpa and of AC and AD is 140Mpa. Consider an overall safety factor of 3.3 and θ= 30°.
The AB bond must be made of a steel for which the normal stress limit is 450 MPa. Determine the cross-sectional area for AB for the which the safety factor is 3.50. Suppose the link is adequately reinforced around the pins at A and B. What is the deformationof bar AB when subjected to the load applied to it considering the modulus of elasticity of steel E = 210 Gpa and the length L of thebar equal to 0.75m (All dimensions are in meters)?
The horizontal link BC is 1/4 in. Of thickness and width w = 1.25 in., It is made of steel with an ultimate tensile strength of 65 ksi. What is the factor of safety if the structure shown was designed to support a load P 10 kips?
Static Problem. Indications:The system shown is composed of an ABG bar, supported by a pin at point A and by a collarsmooth at point B (the collar slides on the bar ABG). The collar is pinned to the BDE bar, and theRod BDE is supported by a pin at D and a cable at end E.Based on the above, determine:a) The load P, such that the cable force EF is T.b) The internal loads in a section passing through point G (normal and shear force, and momentflexing).c) Draw bar BDE horizontally and generate the shear force and moment diagramsflexing Indicate the maximum values of shear force and bending moment and their location.?= 22 lb ? = 7 in ? = 6 in
If the bolt length is 220 mmmm and the sleeve length is 200 mmmm, determine the tension in the bolt when a force of 50 kNkN is applied to the brackets. Express your answer to three significant figures and include appropriate units. Given: The bolt AB in (Figure 1) has a diameter of 21 mmmm and passes through a sleeve that has an inner diameter of 42 mmmm and an outer diameter of 52 mmmm. The bolt and sleeve are made of A-36 steel and are secured to the rigid brackets as shown.