Two pieces of 1x4 lumber are glued together at an angle = 30° as shown. Each piece of wood has actual cross-sectional dimensions of 0.75 in x 3.5 in. The adhesive used has normal strength SN = 1350 psi and shear strength Sy = 750 psi when bonded to the lumber. Determine the largest axial force that can be safely applied to the glue joint. F 10 Fmax number (rtol=0.01, atol=1e-05) lbf F

Two pieces of 1x4 lumber are glued together at an angle = 30° as shown. Each piece of wood has actual cross-sectional dimensions of 0.75 in x 3.5 in. The adhesive used has normal strength SN = 1350 psi and shear strength Sy = 750 psi when bonded to the lumber. Determine the largest axial force that can be safely applied to the glue joint. F 10 Fmax number (rtol=0.01, atol=1e-05) lbf F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the bolt length is 220 mmmm and the sleeve length is 200 mmmm, determine the tension in the bolt when a force of 50 kNkN is applied to the brackets. Express your answer to three significant figures and include appropriate units. Given: The bolt AB in (Figure 1) has a diameter of 21 mmmm and passes through a sleeve that has an inner diameter of 42 mmmm and an outer diameter of 52 mmmm. The bolt and sleeve are made of A-36 steel and are secured to the rigid brackets as shown.
A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, £ = 100 GN/m2
(a) Assess the stability of the wedge formed from intersection of the two joint planes with the face of a wall slope dipping 56° at dip direction 329°, or briefly shown as (56°/329°). The dip and dip direction for the two joint sets are as follows. Joint Set 1: (41°/51°), Joint Set 2: (40°/326°). Joint planes are assumed to have no cohesive resistance (C = 0) and their friction angle (‹= phi) is assumed to be the same for both joint sets and equal to 26°.
Why is is that when I compute for the diameter, the answer is 7.9706? How was 13.22 obtained? Bartleby link for solution: https://www.bartleby.com/questions-and-answers/a-steel-rod-is-stretched-between-two-rigid-walls-and-carries-a-tensile-load-of-5000-n-at-20c.-if-the/5c99ed3b-d083-41be-a905-b15aa3bc8648
plates 1 and 2 are glued together as shown in the figure. The tensile strength of the adhesive is 235 kN/cm^2, its shear strength is 175 kN/cm^2. With the glue evenly distributed over the rectangular surface (30mm x 70mm), determine the allowable tensile force F for the assembly.
A square post which is made up of two parts is glued atplane ABCD with the angle α = 30° with the vertical.Allowable compressive stress @ glue = 5.2 MPaAllowable shearing stress = 3.5 MPaP = 36 kN. 1. What is the minimum post dimension, w (mm), withoutexceeding the allowable shearing stress at the glue? 2. What is the minimum post dimension, w (mm), withoutexceeding the allowable compressive stress at the glue? 3. What angle, α, will give the maximum shearing stress? with brief explanation each part
In the graft, the 6-meter-high arm is manufactured using the l profile given below. It is fixed to both ends of the arm with a built-in support. If the yield strength of the material is σy=400 MPa Elasticity modulus E=2*105 MPa If the safety factor used in the design is 2.5, the arm in question is What is the highest axial load it can safely carry?
Seatwork: Show your complete solution. Use 4 decimal places. Poisson’s Ratio: A square bar of aluminum 40 mm on a side and 220 mm long is loaded by axial tensile forces at the ends. Experimentally, it is found that the strain in the direction of the load is 0.001. Determine the volume of the bar when the load is acting. Considering a Poisson’s ratio of 0.33
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680 MPa, and for the bronze (σY)br=490 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa.
Cylinders 1 and 2 are glued as shown in the figure. The tensile strength of the glue is 24 MPa, its shear strength is 18 MPa. The glue is evenly distributed over the cylinder with a diameter of 30 mm and an unknown length L. The force F supported by the assembly is 2,600 daN. Calculate the minimum length L to give to the glued joint of the assembly.
NEED ANSWER ASAP !!! The axial load 274 kN applied to the lap joint is distributed equally among the three 26.5-mm-diameter rivets. What is the bearing stress (in MPa) between a plate and a rivet if w = 135.4 mm and t = 29.5 mm?
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?