Two pumps having the same specifications and power are connected in series to deliver a flow rate of Q (m³/s) water from the lake to a large tank. The total height from the lake to the tank is 2h. The irreversible losses are given by hL. - Determine the pressure difference across the two pumps (between points A and B) Determine the pressure difference across pump 2 (between points C and B) - h = (Last two digits of Matric no +80) m hL = (Last two digits of Matric no + 7) m

Two pumps having the same specifications and power are connected in series to deliver a flow rate of Q (m³/s) water from the lake to a large tank. The total height from the lake to the tank is 2h. The irreversible losses are given by hL. - Determine the pressure difference across the two pumps (between points A and B) Determine the pressure difference across pump 2 (between points C and B) - h = (Last two digits of Matric no +80) m hL = (Last two digits of Matric no + 7) m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HYDRAULICS Oil with specific gravity of 0.75 is flowing through a 6 inch pipe under a pressure of 15 psi. If the total energy relative to a datum plane 8 ft below the center of the pipe is 58.6 ft-lb/lb. Determine the discharge of oil.
A water pump motor has a horsepower rating of 11.3 HP. If it is to pump water from a well at the rate of 1 ft³/s, what is the minimum depth the well may have? The correct answer is 100 ft.
A 5 kW electric motor driving a pump has an efficiency of 85%. Determine the losses encountered in the driver.
A 20-KW motor with 80% efficiency drives a centrifugal pump delivery 0.08m3/sec against a head of 20m. Determine the pump efficiency
Water is being pumped from an atmospheric source on the ground at the rate of 200 liter/minute to a pressurized tank on top of an office building through a constant diameter pipe. The discharge to the pressurized tank is 20 meters off the ground and the tank has a gauge pressure of 5 bar. Ignoring frictional losses, determine the a)power the pump must supply the fluid in W (Correct Answer is 2321 W) By performing an energy balance around the pump and ignoring friction and any changes in height between the inlet and outlet of the pump determine the: b) increase in pressure across the pump in psi (Correct Answer is 101 psi)
Oil with specific gravity of 0.75 is flowing through a 6 inch pipe under a pressure of 15 psi. If the total energy relative to a datum plane 8 ft below the center of the pipe is 58.6 ft-lb/lb. Determine the discharge of oil.
A pump is driven by an electric motor moves 35 gal/min of water from reservoir A to reservoir B, lifting the water to a total head of 245 ft. The efficiency of the pump and motor are 64% and 84% respectively. What size of motor (HP) is required? a. 3 hp b. 5 hp c. 4 hp d. 7 hp
Water enters through a 500 mm diameter inlet pipe under a pressure of 15 kPa. It leaves through a 1000 mm diameter exhaust pipe with a pressure of 5 kPa. If the center of the outlet pipe is 3 m above the center of the inlet pipe and 500 L/sec of water passes a motor or pump. Which of the following most nearly gives the specific gravity of the block? a. 1.6320 b. 0.6814c. 0.3196 d. 1.3186
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. Choices are listed below and draw its FBD. A.-4.67 m B.-2.72 m C.12.74 m D.2.56
1. The figure shows a pump that draws 840 L/min of crude oil (s= 0.85) in an underground storage drum to the first stage of a processing system; a) If the total energy loss in the system is 4.2 N m/N of oil flow, determine the power transmitted by the pump to the fluid. b) If the energy loss in the steel suction line is 1.4 N m/N of oil flow, determine the pressure at the pump inlet
kindly help me with this problem INSTRUCTIONS: Solve the problems neatly and systematically. SUse free-floating decimals in all your calculations and in expressing your answers. Box your final answers. 5. In reference to problem number 1, if another pump was used having a power requirement of 12 hP with an efficiency of 73% in pumping the water at 1.2 ft3/s through a constant diameter of a pipe. Determine theirreversible head loss of the piping system in ft of water if the free surface of the pool was at 35 ft?
A fan with 22-in-diameter blades moves 1800 cfm (cubic feet per minute) of air at 70°F at sea level. Determine the following: The force required to hold the fan. The minimum power input required for the fan Choose a control volume sufficiently large to contain the fan, with the inlet sufficiently far upstream so that the gage pressure at the inlet is nearly zero. Assume air approaches the fan through a large area with negligible velocity and air exits the fan with a uniform velocity at atmospheric pressure through an imaginary cylinder whose diameter is the fan blade diameter.