Two reservours with different liquilds A (s.g 0.8) and B (s.g 1.5) are connected by a Im square opening hole. The homogeneous cylinder (s.g 2.0), with 1 m long, is used to block the hole. Determine the magnitude and direction of the reactions at the upper and lower edges (s and m) of the opening.

Two reservours with different liquilds A (s.g 0.8) and B (s.g 1.5) are connected by a Im square opening hole. The homogeneous cylinder (s.g 2.0), with 1 m long, is used to block the hole. Determine the magnitude and direction of the reactions at the upper and lower edges (s and m) of the opening.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.153P: Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.

See similar textbooks

Related questions

Q: A cantilever beam is supported at B by cableBC. The beam carries a uniform load q = 200 N/m.If the…

A: Let us suppose that there is no cable at the end B of the beam, thus the deflection of point B in…

Q: Two reservours with different liquilds A (s.g 0.8) and B (s.g 1.5) are connected by a Im square…

Q: .Find the reactions at support points 145 N/M B 10M

A: When a given system is in equilibrium, then the net external force acting on the system is equal to…

Q: E Find the Reactions at pont A where the tensile force in cable CB is 300 KN. Neglect weight of AB.…

A: Consider the Free Body diagram:

Q: Draw the F.B.D. for the beam shown in fig and then find the reactions at A and * ? B 9 kN/m 3 m 3m

A: We have given a beam with symmetric triangular loading . Beam supported by its two end by reaction…

Q: Two smooth spheres each of radius 100mm and weighing 100N, rest in a horizontal channel having…

A: Given data: The free body diagram of the Rollers 1 and 2 are shown below,

Q: A man raises a 10-kg joist with a length of 4 m by pulling on a rope.Find the tension T in the rope…

A: Given Data: The mass of the joist is M = 10 kg. The length of the joist is L = 4 m. The tension in…

Q: - A tskN) cylinder is supported by beam AB and a cable as shown in Fig· bleow. Determine the…

Q: A cylinder with a radius of 1.5 m and a weight of 40 kN is held by the rod AD. Find the force at CD…

A: The free-body diagram of the cylinder Applying equilibrium conditions: ∑Fy=0REcos300-40=0RE=46.188…

Q: Determine the reactions for the frame shown in Fig., by the method of least work. ElI is constant.

A: Structure is supported by fixed supports at point A and point D. Let Horizontal reactions at point A…

Q: The horizontal cylinders in the figure shown are piled in a rectangular ditch. Radius of cylinders…

Q: For the structure loaded as shown in the figure, determine reaction at A *

Q: Compute the moment of area of the M diagram between the reactions about both the left and the right…

Q: Find the reaction in pin A?

Q: Find the reaction in pin A ?

A: Consider the free body diagram shown below for the given system.

Q: For the force at C, find the reactions at D, E, and A.

A: Solution: given dataF = 10 lb

Q: Two identical rollers, each of weight W = 100 lbf, are supported by an inclined plane and vertical…

A: Given; W=100 lbf Angle θ=30° To Find, RA,RB and RC

Q: An overhang beam is situated above a cantilever beam carrying its roller support. Determine the…

Q: wo smooth spheres each of radius 100 mm and weighing 100N, rest in a horizontal channel having…

A: When three forces which are concurrent & coplanar are in nature act at a point simultaneously at…

Q: ne uniform 18kg Bar OA is held in the position shown by a smooth pin at O, and the cable AB which is…

A: givenuniform bar AO mass, m=18kgangle maked by bar AO with horizontal axis,θ=600length of the bar…

Q: A 85 kg baby elephant stands on a homogeneous beam of mass 210 kg. Find the reaction forces at…

A: The free-body diagram is shown below.

Q: Solve for the reactions at A.

Q: Compute for the reaction at A Compute for the reaction at D

Q: Draw the F.B.D. for the beam shown in fig and then find the reactions at A *? and B

Q: The moment reaction at B is

Q: Show that in a hollow circular section chimney of external diameter D and internal diameter d, the…

Q: Find the reactions at the support A and B in the system below.

Q: Solve the total reaction at A in kN.

A: Free Body Diagram of the beam, At equilibrium condition, Horizontal forces acting on the beam,…

Q: Find the reaction at B Weight of the beam is 43 kg include this too. Please solve

A: Given Datam=43kgW=43×9.81=0.422kN

Q: A and vertical pin reaction at D are respectively. Note: the reaction force at A E. and E have only…

A: Take equilibrium conditions (moment at any hinge is zero, summation of vertical force is zero) for…

Q: the magnitude of the force P required to maintain equilibrium of the ladder is

A: Given; A ladder AB of length L=5mWeight, W=600NAssuming frictionless contact at the floor (b) and…

Q: In the mechanism shown, find the force P and all reaction forces. Ignore weight forces and friction

A: Considering that the mechanism is in equilibrium with the action of the applied torque and external…

Q: Осean Marsh d = 9 ft 5.79 A freshwater marsh is drained to the ocean through an automatic tide gate…

A: Given, b=4 ft=1.219 m, t= 3 ft= 0.914 m h= 6 ft= 1.828 m, d= 9 ft= 2.7432 m, w= 64 lb/ft3=10053.54…

Q: Use the principle of virtual work, determine the support reactions in the beam ABCD shown; By L/2…

A: Virtual Displacement: As we know, if we apply a force on an object there will be some displacement.…

Q: 2. The uniform pole has a weight of W and is supported by its smooth ends against the vertical walls…

Q: Draw the F.B.D. for the beam shown in fig and then find the reactions at A and B ? If Wo= 1500 Ib/ft…

Q: Draw the F.B.D. for the beam shown in fig * ? and then find the reactions at A and B

A: Consider the free body diagram shown below for the given beam.

Q: El mecanismo mostrado consiste en una manivela (barra AB), una biela (barra BC) y el pistón C que se…

Q: A uniform horizontal beam with a length of 1.7 m and a weight of 200 N is attached to a wall by a…

Q: calculate the reaction forces

A: To find: i) Reaction at A (Ra) ii) Reaction at B (Rb) The reactions can be found out by…

Q: Determine the reactions at A and B shown in Figure below, neglect the weight of beam

Q: sosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force (P s…

Q: Calculate the reactions at D

Q: Draw the F.B.D. for the beam shown in fig and then find the reactions at A * ? and D

Q: Q4) Calculate the reactions at supports. 400 N/m 400 N /m

A: Given

Q: A body consisting of a cone and hemisphere of radius (r) on the same base rests on a table, the…

A: Draw sketch for given condition for better understanding

Q: Determine the reactions at A and B for the loaded beamas shown in Figure

Q: A ball of weight 120 N rests in a right angled groove as shown in Fig. The sides of the groove are…

Q: A rectangular gate (6m x 4m) is e hinged at A and supported by a stopper as shown. Find the reaction…

A: Given: The area of gate, A = 24 m2 The centre of pressure measured from A, yp = 3+0.4641 = 3.4641 m…

Concept explainers

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.

Question

Two reservours with different liquilds A (s.g 0.8) and B (s.g 1.5) are connected by a Im
square opening hole. The homogeneous cylinder (s.g 2.0), with 1 m long, is used to block the
hole. Determine the magnitude and direction of the reactions at the upper and lower edges (s
and m) of the opening.
B
S=0.8
6m
A
S=1.5
5m
450
Im
Page 1 of 6

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step by step

Solved in 7 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q 244 What are the reaction forces on the latch an djoint in the gate below? And in case thefloodgate is reversed (concave)? *The gate is a cylinder room with length L = 5 m
The 3 × 4-m side AB of a tank is hinged at its bottom A and is held in place by a thin rod BC. The maximum tensile force the rod can withstand without breaking is 200 kN, and the design specifications require the force in the rod not to exceed 20 percent of this value. If the tank is slowly filled with water, determine the maximum allowable depth of water d in the tank.
What are the reaction forces on the latch an djoint in the gate below? And in case thefloodgate is reversed (concave)? *The gate is a cylinder room with length L = 5 m
One end of a rod of length L and density ρ is fixed by a frictionless pivot at a depth d under water. Determine the equilibrium positions of the rod in terms of its angle α measured from the vertical, and the investigate whether the equilibrium positions are stable or unstable, given that (a) ρ = 500 kg/m3 ; (b) ρ = 853 kg/m3 (The density of water is ρw = 1000 kg/m3 .)
A caisson for closing the entrance to a dry dock is of trapezoidal from 16 m wide at the top and 12 m wide at the bottom and 8 m deep. Find the total force in MN on the caisson if the water on the outside is 1 m below the top level of the caisson and the dock is empty. enclude your free body diagram. a.117.72 b.80.93 c.3.164 d.37.77
- A 3.5m - high . 5m wide rectangular gate is hinged at the top edge at A and is restrained by a fixed ridge at B. Determine the force exerted on the gate at Point B
Please give right answer otherwise skip to another expert. Show that in a hollow circular section chimney of external diameter D and internal diameter d, the resultant line of thrust due to lateral pressure and self-weight should fall within (D^ 2 -d^ 2 )/8D of the centre line of the chimney for no tension at the base.
A dam with triangular cross section holds back a body of water. The dam has height h. The dam is made of concrete, which has speci…c gravity 3.1. What is the maximum angle, , for which thedam will not tip over about point O?
A gate AB 4 ft long and 2 ft wide is held in position shown due to the spring whose constant is 96.0 Ibf/in. The spring is located compressed 1.5 ft in such a way as to keep the gate in equilibrium. Assume that on the gate (which moves through a circular sector BD as shown in Fig. figure), the force due to the spring is always horizontal. Determine the height d of the water.
A cable with supports at the same elevation has a span of 300m. The cable weighs 75 N/m and the sag at midspan is 75 m. Determine The length of the cable.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
can you help me solve this problem with complete solution and free body diagram