Two resistors are connected in series. One resistor has a resistance of 1000 ohms, and the other resistor value is unknown. the circuit is connected to a 50V power supply and there is a current of 25mA flowing in the circuit. if a 1500 ohms resistor is connected in parallel with the unknown resistor, how much current will flow in this circuit?

Two resistors are connected in series. One resistor has a resistance of 1000 ohms, and the other resistor value is unknown. the circuit is connected to a 50V power supply and there is a current of 25mA flowing in the circuit. if a 1500 ohms resistor is connected in parallel with the unknown resistor, how much current will flow in this circuit?

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter27: Service-entrance Equipment

Section: Chapter Questions

Problem 40R

See similar textbooks

Similar questions

Three wire-wound resistors have the following values: 30 Ohms, 80 Ohms, and 100 Ohms. Each resistor has a voltage rating of 100-V. If these three resistors are connected in series , can they be connected to a 240-V circuit without damage to the resistors? Explain your reasoning.
Three resistors, 1.1 Ω, 9.0 Ω, and 3.2 Ω, are wired in series with a power source of 7.3 volts. Calculate the potential difference in Volts across the 1.1 Ω resistor. Use 2 significant figures in your answer. Hint: The same current must go through all three resistors, so the equivalent resistance Req ( the sum of the resistances) can be used with Ohm's Law to find the current. The current, must then produce a voltage drop I * R1 across the first resistor.
A combination of three resistors R1, R2 and R3 in series is connected across a voltage source Vt. The voltage drop across R1 and R3 are 10V and 36V, respectively. If the current supplied by the source voltage is 1.4A and the total power supplied by the source is 70W, Calculate the value of Req-
circuit shown, the Total Resistance is found to be 6 Ohms. Calculate: The value of R2. The required Voltage Source E. please answer the following question with clear explanation, show all the work
For the following circuit: Calculate the Thévenin equivalent between B and A by the test source method and draw the resulting circuit. Draw the Thévenin equivalent if all resistors are In this case, how much will the current through a resistor connected between A and B be worth? Assume that R1 = R2 = R, R3 = R-ΔR and R4 = R+ΔR. How much are t h e Thévenin voltage and resistance worth? Is the Thévenin voltage linear with respect to ΔR?
Eight lamps are always connected in parallel as shown in the Figure.(a) If the set is connected to a 120V source, what is the current through eachlamp whether each internal resistance of 1.8 kohm?(b) Determine the total resistance of the network.(c) Find out the power dissipated in each lamp.(d) If a light bulb burns out (ie opens the filament), what is the effect on theremaining lamps?(e) Compare the parallel arrangement of a figure with a series arrangement. what are the relativesadvantages and disadvantages of parallel system compared to series arrangement? or Oito lâmpadas sempre estão ligadas em paralelo como mostrado na Figura.(a) Se o conjunto está ligado a uma fonte de 120V, qual é a corrente através de cadalâmpada se cada uma resistência interna de 1,8 kohm?(b) Determinar a resistência total da rede.(c) Descubra a potência dissipada em cada lâmpada.(d) Se uma lâmpada queima fora (ou seja, abre o filamento), qual é o efeito sobre aslâmpadas restantes?(e) Compare o arranjo…
NEED ASAP!! SOLVE CORRECTLY 4 resistors are connected as shown in the figure. The total current passing through the circuit is 5A while the current R1 has a resistance of 3 ohms.The voltage across R2 and R4 are 20V and 30V respectively and the current passing through R3 is 2A. determine the total voltage and total resistance of the circuit and shown and all other unknowns
Circuit analysis: A circuit is shown below with three resistors & +10V source. Calculate each voltage, current, and dissipated power to each resistor where the resistors’ color codes are: R1=Red-Black-Red-Gold, R2= Yellow-Black-Red-Brown, R3= Grey-Black-Red- Gold. Fill in the blanks in the following tables.
This question centers around two ways to model a load attached to a source. In both of the figures below, the source is the circuit comprising the 240V voltage source and the 25K and 75K resistors. Figure 1 Figure 2 In Figure 1, suppose we connect (short) a to a′ and b to b′. Calculate v0. As an alternative, calculate v0 if the load is connected to the source as in Figure 2. Comment on the differences between your answers to parts A and B.
For the circuit shown below, If the 10-k resistor is replaced by an 18-k resistor, what resistor connectedbetween terminals a − b absorbs the maximum power? What is this power?.
A resistance connected in parallel with an ideal voltage source can be removed without affecting the remaining circuit. explain with right answer... Select one: True False
The circuit shows a variable resistor, with a lamp (L) connected to an ammeter and a voltmeter. By inspection, the circuit shown demonstrates that a) the variable resistor and voltmeter should be interchanged b) the lamp L and voltmeter should be interchanged c) the ammeter should be parallel with R, not with the lamp L d) the voltmeter and ammeter should be interchanged