A 19 ft long, simply supported beam is subjected to a 5 kip/ft uniform distributed load over its length and 11 kip point load at its center. If the beam is made of a W14x30, what is the deflection at the center of the beam in inches? The quiz uses Esteel = 29,000,000 psi. Ignore self-weight. X 0.19556 Correct Answer: 2.06

A 19 ft long, simply supported beam is subjected to a 5 kip/ft uniform distributed load over its length and 11 kip point load at its center. If the beam is made of a W14x30, what is the deflection at the center of the beam in inches? The quiz uses Esteel = 29,000,000 psi. Ignore self-weight. X 0.19556 Correct Answer: 2.06

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cantilever 8m long carries a uniformly distributed load of 12kN/m from midspan to free end. Determine the deflection at the free end, Find the smallest moment of inertia (in x10^6 mm^4) so that its maximum deflection does not exceed the limit of 1/360 of the span. Use E = 70 GPa. Determine the required depth of beam if it is a rectangular section with width-to-depth ratio of 0.5.
The cross-section is shown to the right of the beam. For the steel beam what is the deflection at the left end? Note: Young’s modulus is 29.0 ksi (ksi – kips/in2)
If a cantilever beam (one end fixed and other end free) has a cross section of 4 mm x 4 mm and a span length of 10 cm has an end load of 70 N, what would be the slope (θ) of the beam in degrees? Modulus of elasticity is given as 70 GPa.
Question 4: Use the moment-area method to determine the slope and deflection at point B for the structure shown in Figure 4 where CD k.ft = 108 k.ft and AB kips = 18 kips.(E = 10 000 ksi, IAB = 1 440 in4, IBC = 720 in4)
the W14 x 43 simply supported beam is made of A-36 steel and is subjected to the loading shown where the distributed load is equal to 2.40 kip/ft. Ix = 428 in4 , E=29 (103) kip determine the beam's deflection at its center, C. give your answer as a signed distance, where up is positive.
A 13 m simply supported beam with a uniform load of 3 kN/m from right end to the left end and has a maximum deflection of __________. Use EI = 11000 kN-m2.
The beam is subjected to the distributed loading as shown. Use E = 30,000 ksi, I = 394 in.4 , L = 23 ft, the max load distribution density at B w0 = 5 kip/ft, calculate the deflection at the middle of the beam: ___ in. Use apendix at end of the textbook and write down all the steps which lead to your anser. Pay attention to unit conversion, and calculate your answer to 1 decimal place
The cross-section is shown to the right of the beam. For the cast iron beam what is the maximum deflection in the beam? Note: Young’s modulus is 172 GPa.
(use EI constant for whole span). A 10-meter-span, propped beam (fixed at the left support and roller at right support), with a uniformly distributed load from left support to six meters to the right, with a magnitude of six kilonewton per lineal meter, a downward concentrated load at the midspan. Solve the reactions at the fixed support and roller support, slope and deflection at the roller support, using Area Moment Method. Use the concentrated load as 24 kN.
8. At what distance a should the bearing supports at A and B be placed so that the deflection at the enter of the shaft is equal to the deflection at its ends? Use MAM. The bearings exert only on the hafts. The flexural rigidity is constant. 9. For this beam example, let's say we are interested in finding the deflections at every key point of the beam (A, C, and E) using the conjugate beam method. 10. Determine the equations of the elastic curve using the coordinates x1 and x3 and specify the slope and deflection at point B. El is constant.
Can the deflection or slope at a point on a member subjected to combinations of loadings be determined with the method of superposition method?
The roof beam of a buidling is subjected to the loading shown in Fig. 1. If a maximum 3/8 inch deflection is permitted at the cantilever end (A) before the ceiling and roofing materials would be damage, calculate the required minimum moment of inerita in inches4 for the beam using theDouble Integration Method. Use ? = 29,000 ?/??2.