i need the answer quickly Two samples of sand are mixed together to get a mixture with finenessmodulus = 2.8. Find the mix proportion.10 5 2.40.15 0.075Sieve size (mm)1.20.60.3Sand (1) (% passing)100979070603055Sand (2) (%passing)1009180503020

We have to determine the value of mix proportion by the data we have samples of sand are mixed…

Two samples of sand are mixed together to get a mixture with fineness modulus = 2.8. Find the mix proportion. %3D 10 5 Sieve size (mm) 2.4 1.2 0.6 0.3 0.15 0.075 Sand (1) (% passing) 97 90 70 100 60 30 5 5 Sand (2) (%passing) 100 91 80 50 30 5 20

Two samples of sand are mixed together to get a mixture with fineness modulus = 2.8. Find the mix proportion. %3D 10 5 Sieve size (mm) 2.4 1.2 0.6 0.3 0.15 0.075 Sand (1) (% passing) 97 90 70 100 60 30 5 5 Sand (2) (%passing) 100 91 80 50 30 5 20

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter3: Weight-volume Relationships And Plasticity

Section: Chapter Questions

Problem 3.1P

See similar textbooks

Related questions

Q: During the 1-dimensional consolidation test, the following measurements were m Before commencement…

A: Disclaimer- According to my calculation right answer is differing from the above given choices ,so i…

Q: . Using the sieve results of a batch of sand and gravel shown in the table below,calculate the…

Q: a. Determine the percent finer than each sieve and plot a grain-size distribution curve. b.…

Q: A sample of sand has the following properties: Moist mass = 625.2 g Dry mass = 589.9 g absorption =…

Q: Given the following data for sand: Mass of sand ( oven-dary) = 480 g Mass of sand (SSD) = 490 g Mass…

A: A = Mass of oven-dry sand = 480 g B = Mass of saturated surface dry (SSD) sand = 490 gW1 = Mass of…

Q: 3- Following are the results of a laboratory consolidation test on a sample of undisturbed clay…

A: Draw the horizontal line from maximum curvature Draw tangent from the maximum curvature point…

Q: 03: A container filled with wet sand has a mass of 203 gm. On drying, the mass becomes 177 gm. The…

Q: 2. The results of Marshall Test for five specimens are given below. Find the optimum bitumen content…

A: The optimum bitumen content can be obtained by taking the average of bitumen content at maximum…

Q: The following are the results of a sieve analysis: Sieve size Weight Retained 9.5mm 0 4.75mm…

A: Introduction- A sieving, also known as a grading test, is a process commonly used in civil and…

Q: Obtain fineness modulus for following sieve analysis data

A: Given: Sieve size (mm) %retained 9.5 0.00 4.75 16.00 2.36 19.00 1.18 12.00 0.6 13.00…

Q: 11. The range of water content between the liquid and plastic limits is termed as: A. liquid limit…

Q: Using the following data, determine whether the total air voids content of the Marshall sample…

Q: A liquid limit test performed on a soil sample has the

A: here water content is given to us and also N = 20

Q: A liquid limit test on a clay was performed with the following results. The natural water content of…

Q: The following data are the results of a sieve analysis Determine the percentage retained on sieve…

Q: Consider the following data in the design of grit chamber : 1. Specific gravity of grit = 2.7 2.…

A: Correct option for this problem is option "b" For explanation please refer the attached solution,…

Q: Discussion: > for fine aggregate (sand): 1. Draw a relationship between sieve size (mm) (x-axis) and…

Q: Example: Marshall test results of surface course for six specimens gave the following results: Unit…

A: As per Marshall specifications, the optimum bitumen content can be found out by taking the average…

Q: 3 The below results are obtained from a sieve analysis done on a sample with dry mass of 1550 g. The…

A: The given data is shown below:

Q: Soil placed on a can has been weighed before and after an oven-drying procedure. The procedure…

Q: The following are the results of a sieve and hydrometer analysis. Analysis Sieve number/grain size…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: The back fill material for a vibroflotation project has the following grain sizes. D10 0.11 mm…

A: Find sorting coeffficient

Q: In a liquid limit, using a cone penetrometer, the following reading were recorded and tabulated as…

A: Given:- The readings were recorded using the cone penetrometer For plastic limit test Trial…

Q: A soil sample has a total volume of 1,485 cc. The specific gravity of the soil solids is 2.74. Then…

Q: Mass of Soil Sieve Opening Sieve # on each Sieve Size (g) 4 4.76 8 45 2.38 10 65 2.0 20 92 0.84 40…

Q: Given a compacted aggregates with a size of 2", given the mass of aggregate plus measure equivalent…

Q: Soil placed on a can has been weighed before and after an oven-drying procedure. The procedure…

Q: A measure of density of compacted fills as part of the specification requirement was performed by…

Q: The back fill material for a vibroflotation project has the following grain sizes. D10 0.11mm D20…

Q: If the readings of a Marshall sample as shown below 1- The maximum load that cause failure of it =…

A: Calculate the volume of voids in mixVV=(Gth-GmGth)×100=(2.52-2.512.52)×100=0.397%Calculate the…

Q: nere: MC = moisture content in percent Mmoist = mass of original specimen Mdry = mass of oven dry…

Q: The mass of oven dried sample of gravel is 300 grams. The absorption is 10% by weight. Determine the…

Q: 3- Following are the results of a laboratory consolidation test on a sample of undisturbed clay…

A: Soil Consolidation: Soil consolidation is the linear process by which soil changes volume in…

Q: n sample of AL Batina soil tested in the laboratory. The gradation analysis results are as shown in…

Q: The following are the results of a sieve analysis: a. Determine the percent finer than each sieve…

A: U.S SIEVE NO DIAMTER (mm) MASS RETAINED (mm) % WT RETAINED % CUMMULATIVE RETAINED % FINER 4 4.75…

Q: If the weight of sample of sand in sieve analysis test was 420 gm and the weight retained on sieve…

Q: The following are the results of a sieve analysis: a. Determine the percent finer than each sieve…

A: Soil boundaries give an idea of its compatibility with soil and water or both compounds. When the…

Q: What is the Summation of cumulative retained percentage for the Gravel * 1.524 2.509 3.424 4.624…

A: Tabulate the following. Sieve No. Amount retained Sand (g) Percent retained sand (g) Cumulative…

Q: In a sieve analysis test, 95.5% of the sample is passing the 5mm sieve and 5.13% is passing sieve…

A: 1)clay = less than 2 micron 2)silt = 2 micron to 75 micron 3)sand = 75 micron to 4.75mm 4)Gravel =…

Q: From the results of a sieve analysis, shown below, determine: (a) the percent finer than each sieve…

A: Given data

Q: A soil sample has a total volume of 1,428 cc. The specific gravity of the soil solids is 2.70. Then…

Q: Determine the Fineness Modulus of the sand given its sieve analysis in the following table. round to…

Q: Determine the percent finer than each sieve and plot a grain-size distribution curve. Determine D10,…

A: MAKE A TABLE

Q: SITUATION 2: From the following data of a given sieve analysis: Sieve No. # 4 #8 #10 # 25 #60 #100…

Q: a. Determine the percent finer than each sieve and plot a grain-size distribution curve. b.…

A: The number of voids divided by the volume of solids is the void ratio of a mixture. Soil organic…

Q: Determine: 1. The percent finer in Sieve # 20 2. The percent finer in Sieve # 80 3. D60from the…

A: Find out : 1) % finer than sieve no 20 2) % finer than sieve no 80 3) D60 4) D30 5) D10 6) Cu…

Q: From the results of a sieve analysis, shown below, determine: (a) the percent finer than each sieve…

Q: The following results were obtained from a liquid limit test on a clay using the Casagrande cup…

A: Given data Number of blows against water content Natural water content According to guidelines…

Q: Three samples of aggregates were taken weighed in moist and dry condition. Moist Dry Unit Absorption…

A: Given data, Unit weight of water = 9.81 kN/m³ To find out the average free moisture content of…

Q: Question 4 Comment the four types of sieve analysis diagrams, which appear in the figure below:…

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

i need the answer quickly

Two samples of sand are mixed together to get a mixture with fineness
modulus = 2.8. Find the mix proportion.
10 5 2.4
0.15 0.075
Sieve size (mm)
1.2
0.6
0.3
Sand (1) (% passing)
100
97
90
70
60
30
5
5
Sand (2) (%passing)
100
91
80
50
30
20

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve this problem The following data are given for a channel-type grit chamber of length 7.5 m. 1. Flow through velocity = 0.3 m/s 2. The depth of waste water at peak flow in the channel = 0.9 m 3. Specific gravity of inorganic particles = 2.5 4. g 9.80 m/s², μ = 1.002 x 10-3 N-s/m² at = 20°C, Pw = 1000 kg/m³ Assuming that the Stoke's law is valid, the smallest diameter particle that would be removed with 100% efficiency is
An aggregate sample has a compacted dry unit weight of 1615 kg/m3 and a dry specific gravity of 2.15 If this aggregate is placed in a container and compacted with the same procedure used in the determination of compacted unit weight, what will be the amount of pores, in percent of the container volume, between the aggregate particles? (density of water = 1000 kg/m3)
You are asked to design a water softening system to bring following water to a final hardness if 75.0 mg/L as CaCO3. The ion concentrations reported below are all mg/L as CaCO3. Ca2+ = 240.00; Mg2+ = 90.0; HCO3- = 268.0; and CO2= 18.0 The total lime required and initial NCH are nearly 1. 330 and 268 mg/L as CaCO3 2. 376 and 62 mg/L as CaCO3 3. 330 and 27 mg/L as CaCO3 4. 376 and 268 mg/L as CaCO3
Solve as soon as possible -- The following data are given for a channel-type grit chamber of length 7.5 m. 1. Flow through velocity = 0.3 m/s 2. The depth of waste water at peak flow in the channel = 0.9 m 3. Specific gravity of inorganic particles = 2.5 4. g 9.80 m/s², μ = 1.002 x 10-3 N-s/m² at = 20°C, Pw = 1000 kg/m³ Assuming that the Stoke's law is valid, the smallest diameter particle that would be removed with 100% efficiency is
A modified Proctor compaction test was carried out using a cylindrical moldwith a 1000 ml volume. Table 2 summarizes the results. a. Plot the compaction and ZAV curves (RD=2.75 and ρwater=1000 kg/m3)b. Determine the maximum dry density and the optimum moisture content Table 2 Moisture Content (%)Mass of WetSample (g)10.5 2033.211.8 2146.613.0 2203.514.9 2183.116.4 2147.617.6 2116.8
Class No= 5202 A 500 g sample of sand in the SSD condition was placed in a jar, which was then filled with water. The combined weight was (your class Number + 1600) g. The weight of jar filled with water only was 1400g. Estimate the bulk specific gravity (SSD) of the sand.
determine the effective specific gravity of aggregates. DATA: Specific Gravity: Fine Agg = 2.603 Coarse Agg = 2.740 Asphalt Cement = 1.048 Percent By Weight: Fine Agg = 47.90 Coarse Agg= 47.78 Asphalt Cement= 100-FA-CA
In a sieve analysis test, 95.5% of the sample is passing the 5mm sieve and 5.13% is passing sieve #200, which of the following is correct about this sample: There is no clay in the sample the percent of silt and clay is: 5.13% There is 4.5% Sand and Gravel in the sample 95.5% of the sample is Sand and Silt
Soil placed on a can has been weighed before and after an oven-drying procedure. The procedure yeields the following results: Mass of soil + can before placing in the oven (82.2g) Mass of soil + can after placing in the oven (73g) Mass of can (34.5g) If the specific gravity of the soil is 2.78, and the void ratio is 0.636, what will be the moist unit weight (kn/m3) of the soil? Use stored value. Answer to 5 decimal places.
The following are the results of a sieve analysis: a. Determine the percent finer than each sieve and plot a grain-size distribution curve. b. Determine D10, D30, and D60 from the grain-size distribution curve. c. Calculate the uniformity coefficient, Cu. d. Calculate the coefficient of gradation, Cc. e. Plot the particle-size distribution curve Answer in complete solution
A sample of 500 g dry, when poured into a 2 litre capacity cylinder which is partially filled with water, displaces 188 cm³ of water. The density of water is 1 g/cm³. The specific gravity of the sand is
50 kg of gravel is mixed with 30 kg of sand. The gravel has a moisture content of 3.9% and absorption of 4.7%, whereas the sand has a moisture content of 3.5% and absorption of 4.9%. What is the amount of water required to increase the moisture contents of both gravel and sand to reach absorption? Why is it important to determine the amount of water required to increase the moisture content of aggregate to reach absorption?