A soil sample has a total volume of 1,485 cc. The specific gravity of the soil solids is 2.74. Then oven dry sample weight is 2,385 grams. What is the volume of the voids(in cc) in the sample? Answer in TWWO(2) decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.

A soil sample has a total volume of 1,485 cc. The specific gravity of the soil solids is 2.74. Then oven dry sample weight is 2,385 grams. What is the volume of the voids(in cc) in the sample? Answer in TWWO(2) decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter4: Plasticity And Structure Of Soil

Section: Chapter Questions

Problem 4.4P: Results from a liquid limit test conducted on a soil are given below. a. Determine the liquid limit...

See similar textbooks

Similar questions

Results from a liquid limit test conducted on a soil are given below. a. Determine the liquid limit of the soil. b. If it is known that the PI = 6.5, what would be the plastic limit of the soil? c. Determine the liquidity index of the soil if win situ = 23.8%
Refer to Problem 2.C.1. Results of the sieve analysis for Soils A, B, and C are given below. To obtain a more representative sample for further geotechnical testing, a ternary blend is created by uniformly mixing 8000 kg of each soil. Answer the following questions. a. If a sieve analysis is conducted on the mixture using the same set of sieves as shown above, compute the mass retained (as a percentage) and cumulative percent passing in each sieve. b. What would be the uniformity coefficient (Cu) and the coefficient of gradation (Cc) of the mixture?
A soil sample collect near the stadium has a volume of 0.05 m3 and a mass of 87.5 kg. Assume the water content is 15% and the specific gravity of solids (Gs) is 68. Draw a block diagram showing all the necessary mass and volume terms. Use the mass and volume values computed above to compute: Void ratio Porosity Dry unit weight in units of kN/m3 Moist unit weight (unit weight of the sample) in units of kN/m3 Degree of saturation
A sample of soil of mass 240 g is to be placed in a cylinder of volume 500 cm³. An additional 382 cm³ of water is required to fill the container. If water content is 22.5% and specific gravity of soil solids is 2.60, 1. Compute the total unit weight. 2. Compute the dry unit weight. 3. Compute the void ratio.
Someone can help me with this one please. A sample of soil obtained from a test pit 2 ft3 in volume has a weight of 210 lb. The entire sample is dried in an oven and found to have a dry weight of 185 lb calculate the water content, wet unit weight, dry unit weight.
A liquid limit test performed on a soil sample has the following results, compute for the approximate value of the liquid limit. Round off your answer to two (2) decimal places. No. of blows = 20 Moisture content = 40.8%
Let us assume that a soil sample taken in the field is taken and it must be identified by the SUCS Method and AASHTO Method. Moisture content = 5.75% Limit liquid = 53.5 Plastic limit = 31.6 Granulometry Sieve % Pass No. 4 100 # 40 68 # 200 54.3 Do you select the best answer? a) Inorganic silt and sand, with low plasticity b) Inorganic clay with low plasticity c) Clay silt, traces of gravel, dark Brown
The Unit weight of a soil sample is 19. 6 Kilo-Newton per cubic meter. Calculate the following: a. Convert the unit in pcf (Pounds per cubic feet). b. Density in pcf (pounds per cubic feet). c. If the soil has a mass of 3 slugs, determine the volume of the soil in cubic feet. Show complete solution.
Please answer the question below. It would be a big help. Thank you. Please be clear with your answer. Box the final answer. Given the following characteristics of a soil sample: Volume = 0.5 ft3Mass = 56.7 lbThe solids specific gravity of 2.69. After oven drying, the mass of the soil has 48.7 lbs.a) What is the density of the in-situ soil?b) What is the porosity of the in-situ soil?c) What is the degree of saturation of the in-situ soil?
The porosity of a silty sand soil sample is found to be 0.309. Its initial weight is 274.471 grams, and after oven drying for 24 hours, it reduces to 244.321 grams. If the density of the soil solids is 2581 kg/m3, determine the following:Bulk unit weight, Volume of voids, Volume of water to be added/evaporated per cubic meter of soil to attain 50% degree of saturation
The Unit weight of a soil sample is 19. 6 Kilo-Newton per cubic meter. Calculate the following: a. Convert the unit in pcf (Pounds per cubic feet). b. Density in pcf (pounds per cubic feet). c. If the soil has a mass of 3 slugs, determine the volume of the soil in cubic feet.
Give an example of how to convert a mg/L solution extract from a soil to mol/kg solid. (show dimensional analysis).