Two shunt generators A and B operate in parallel and their load characteristics maybe taken as straight lines. The voltage falls from 240V at no load to 200V at200A, while that of B falls from 245V at no load to 220V at 150A. Determine the bus bar voltage when supplying 66.9KW load. How is the load divided between two generators

Two shunt generators A and B operate in parallel and their load characteristics maybe taken as straight lines. The voltage falls from 240V at no load to 200V at200A, while that of B falls from 245V at no load to 220V at 150A. Determine the bus bar voltage when supplying 66.9KW load. How is the load divided between two generators

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.24P: For Problem 3.18, the motor operates at full load, at 0.8 power factor leading, and at a terminal...

See similar textbooks

Similar questions

With the same transformer banks as in Problem 3.47, Figure 3.41 shows the oneline diagram of a generator, a step-up transformer bank, a transmission line, a stepown transformer bank, and an impedan load. The generator terminal voltage is 15 kV (line-to-line). (a) Draw the per-phase equivalent circuit, aounting for phase shifts for positive-sequence operation. (b) By choosing the line-to-neutral generator terminal voltage as the reference, determine the magnitudes of the generator current, transmiss ion-line current, load current, and line-to-line load voltage. Also, find the three-phase complex power delivered to the load.
Consider a three-phase generator rated 300MVA,23kV, supplying a system load of 240 MA and 0.9 power factor lagging at 230 kV through a 330MVA,23/230Y-kV step-up transformer with a leakage reactance of 0.11 per unit. (a) Neglecting the exciting current and choosing base values at the load of 100 MVL and 230 kV. Find the phasor currents IA,IB, and IC supplied to the load in per unit. (b) By choosing the load terminal voltage IA as reference, specify the proper base for the generator circuit and determine the generator voltage V as well as the phasor currents IA,IB, and IC, from the generator. (Note: Take into account the phase shift of the transformer.) (C) Find the generator terminal voltage in kV and the real power supplied by the generator in MW. (d) By omitting the transformer phase shift altogether, check to see whether you get the same magnitude of generator terminal voltage and real power delivered by the generator.
Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
Consider the oneline diagram shown in Figure 3.40. The three-phase transformer bank is made up of three identical single-phase transformers, each specified by X1=0.24 (on the low-voltage side), negligible resistance and magnetizing current, and turns ratio =N2/N1=10. The transformer bank is delivering 100 MW at 0.8 p.f. lagging to a substation bus whose voltage is 230 kV. (a) Determine the primary current magnitude, primary voltage (line-to-line) magnitude, and the three-phase complex power supplied by the generator. Choose the line-to-neutral voltage at the bus, Va as the reference Account for the phase shift, and assume positive-sequence operation. (b) Find the phase shift between the primary and secondary voltages.
For Problem 3.18, the motor operates at full load, at 0.8 power factor leading, and at a terminal voltage of 10.45 kV. Determine (a) the voltage at bus 1, which is the generator bus, and (b) the generator and motor internal EMFs.
Two shunt generators A and B operate in parallel and their load characteristics maybe taken as straight lines. The voltage falls from 240V at no load to 200V at200A, while that of B falls from 245V at no load to 220V at 150A. Determine the bus bar voltage when supplying 66.9KW load. How is the load divided between two generators?
Two generators with ratings of 250 MW and 400 MW operate at 50 Hz frequency have governorspeed regulation of 6.0 and 6.4 percent, respectively, from no-load to full-load, respectively. They areoperating in parallel and share a load of 500 MVA. Assuming free governor action, determine the loadshared by each unit.
Two alternators rated 400 MW and 600 MW are operating in parallel. The droopcharacteristics of their governors are 3% and 4% respectively from no loadto full load. Assuming that the alternators are operating at 50 Hz at noload, how would a load of 1000 MW be shared between them? What will be thesystem frequency at this load?
Discuss system demand and generator loading