Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 3150 mm2 and an allowable normal stress of 175 MPa. Bar (2) has a cross-sectional area of A2 = 2900 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 1.9 m, x2 = 2.9 m, y1 = 1.4 m, and y2 = 2.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. (1) B Answer: Pmax = kN

Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 3150 mm2 and an allowable normal stress of 175 MPa. Bar (2) has a cross-sectional area of A2 = 2900 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 1.9 m, x2 = 2.9 m, y1 = 1.4 m, and y2 = 2.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. (1) B Answer: Pmax = kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported rectangular beam of length 6.45m has a width of 437.5mm and an effective depth of692.5mm. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of31 kN/m and 39.5kN/m., respectively. f'c = 28fy = 4201. Calculate the ultimate moment capacity of the beam.2. Calculate the height of the equivalent stress block.3. Determine the number of bars required for this beam
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of692.5. The beam is to be reinforced using 12 ?? bars. The beam supports service dead loads of31 kN/m and 39.5kN/m., respectively. 1. Calculate the ultimate moment capacity of the beam.2. Calculate the height of the equivalent stress block.3. Determine the number of bars required for this beam
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 14 mm and an allowable normal stress of 145 MPa. Pipe (2) has an outside diameter of 48 mm, a wall thickness of 6 mm, and an allowable normal stress of 115 MPa. Assume x1 = 3.4 m, x2 = 2.4 m, and y 1 = 4.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The f'c is 28 and the fy is 420. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of thewhole structure which is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 ?? bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam
Two circular shadts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional stress of the hollow steel shaft in MPa. ( COMPLETE SOLUTION NO ROUNDING OFF)
Two steel [E = 29,800 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.750 in. and a wall thickness of 0.278 in. Pipe (2) has an outside diameter of 3.750 in. and a wall thickness of 0.209 in. Assume L= 10 ft and L›= 15 ft. If the normal stress in each steel pipe must be limited to 15 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).
A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load).
A vertical 4.80-kN load is applied as shown on a wooden post of rectangular cross section, 80 by 120 mm (Fig. 11.40a). (a) Determine the stress at points A, B, C, and D. (b) Locate the neutral axis of the cross section.
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 3450 mm2 and an allowable normal stress of 65 MPa. Bar (2) has a cross-sectional area of A2 = 3300 mm2 and an allowable normal stress of 120 MPa. Assume x1 = 2.1 m, x2 = 3.4 m, y1 = 0.8 m, and y2 = 2.5 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.