Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 130 MPa, determine the minimum diameter required for each rod. Assume P = 96 kN and Q = 145 kN. di dz B Answers: dq = mm. d2 = mm.

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 130 MPa, determine the minimum diameter required for each rod. Assume P = 96 kN and Q = 145 kN. di dz B Answers: dq = mm. d2 = mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter (in mm rounded to the nearest hundredths) required for rod 2. Assume P = 80 kN and Q = 140 kN.
Determine the normal stress (in psi) at point C for the b=2.4-in. by h= 6.1-in. wooden beam shown below if X = 2.9 ft, P = 1201 lb, and θ = 34° . Round off final answer to four decimal places.
Two steel [E=29,600 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 6.500 in, and a wall thickness of 0.257 in. Pipe (2) has an outside diameter of 4.250 in. and a wall thickness of 0.215 in. Assume L_{1} = 13ft and L_{2} = 18fi . If the normal stress in each steel pipe must be limited to 23 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).
The steel shaft with two different diameters rotates at 4.2 Hz. The power supplied to gear C is 68 kW, of which 42 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 58.1 mm, h = 60.6 mm, L = 3.9 m, M = 2.1 m, and G = 83.49 Gpa. Round off the final answer to two decimal places
The frame shown in figure shows three pinned end bars AB,BD, and CD. The bars are of identical material and cross-section 600 mm^2, and the ultimate stress capacity of each is 350MPa. Using factor of safety of 2.5 , determine the ultimate vertical load P that may be applied to the system at point D.
The column is constructed from high-strength concrete and A-36 steel reinforcing rods. If it is subjected to an axial force of 30 kips, determine the average normal stress in each rod (ksi). Each rod has a diameter of 0.58 inch. Esteel = 29 x 103 psi and Econcrete = 4.2 x 103 psi, r = 4 inches
Two identical steel [E = 200 GPa] pipes, each with a cross-sectional area of 2800 mm2, are attached to unyielding supports at the top and bottom, as shown. At flange B, a concentrated downward load of P = 240 kN is applied. Determine the normal stress in the upper pipe (1).
The rigid bar AD is supported by two steel wires of 1.5 mm diameter (E = 200 GPa) and a pinand bracket at D. Knowing that the wires were initially taut, determine the stress in each wirewhen a 1200 N load P is applied at D. What is the corresponding deflection of point D?
For the beam shown, determine the support reactions and draw the stress diagrams.shear and bending moment. EI is constant. Use the force method. I have a correct answer, it is: VA = 44.3 kN (↑); HA = 0 kN; MA = 34.3 kN.m (counterclockwise); VB = 38 kN (↑). I don't know how to get to this result, please show me how to get there step by step
Determine the normal stress (in psi) at point D for the b=2.1-in. by h= 6-in. beam shown below if X = 6.97 in, P = 9468 lb, and F = 2714 lb. Round off final answer to four decimal places.
Set P1 = 30 kN and P2 = 16 kN in Part A Determine the force in member AD, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. View Available Hint(s) FAD= SubmitPrevious Answers Incorrect; Try Again; 4 attempts remaining Part B Determine the force in member BC, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. View Available Hint(s) FBC = SubmitPrevious Answers Incorrect; Try Again; 5 attempts remaining Part C Determine the force in member BD, and state if the member is in tension or compression. Express your answer to three…
Two steel [E = 29,800 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.750 in. and a wall thickness of 0.278 in. Pipe (2) has an outside diameter of 3.750 in. and a wall thickness of 0.209 in. Assume L= 10 ft and L›= 15 ft. If the normal stress in each steel pipe must be limited to 15 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).