I need the answer as soon as possible Two solid cylindrical rods AB and BC are welded together at B and loaded as shown.Determine the normal stress at the midsection of (a) rod AB, (b) rod BC.0.3m0.2m30 kNBP= 40 kN30 kN3 m4 mFigure (1)Ans. (GAB = 1.27 MPa , GBC= 0.283 MPa

Answered: Image /qna-images/answer/0a54789b-f3e7-4760-9558-5c5539130341.jpg

Two solid cylindrical rods AB and BC are welded together at B and loaded as show: Determine the normal stress at the midsection of (a) rod AB, (b) rod BC. 0.3m 0.2m 30 kN B C P= 40 kN 30 kN 3 m 4 m Figure (1) Ans. (GAB = 1.27 MPa , GBC= 0.283 MPa

Two solid cylindrical rods AB and BC are welded together at B and loaded as show: Determine the normal stress at the midsection of (a) rod AB, (b) rod BC. 0.3m 0.2m 30 kN B C P= 40 kN 30 kN 3 m 4 m Figure (1) Ans. (GAB = 1.27 MPa , GBC= 0.283 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam shown, determine the support reactions and draw the stress diagrams. shear and bending moment. EI is constant. The rigth answer is: VA = 1.3 kN (↑); HA = 0 kN; MA = 4.40 kN.m (clockwise); VB = 51.20 kN (↑). I don't know how to get these results, please show how, step by step.
A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an aluminum alloy (E = 10,000 ksi) pipe B as shown. The supports at the top of the rod and the bottom of the pipe are rigid, and the materials were unstressed before the load was applied. The cross-sectional areas of rods A and pipe B are 0.80 in2 and 3.00 in2 respectively. Determine The normal stress in rod A in ksi, The normal stress in pipe B in ksi and The displacement of plate C in inches. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 5 decimal places.
Two forces P1 and P2, of magnitude P1 = 15 kN and P2 = 18 kN, are applied as shown to the end A of bar AB, which is welded to a cylindrical member BD of radius c= 20 mm. Knowing that the distance from A to the axis of member BD is a= 50 mm and assuming that all stresses remain below the proportional limit of the material, determine the following: 1. What is the absolute value of the axial stress at point K of the transverse section of member BD located at a distance b = 60 mm from end B in MPa. 2. What is the flexural stress at point K of the transverse section of member BD located at a distance b = 60 mm from end Bin MPa. 3. What is the total normal stress at point K of the transverse section of member BD located at a distance b = 60 mm from end B in MPa.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter (in mm rounded to the nearest hundredths) required for rod 2. Assume P = 80 kN and Q = 140 kN.
A hollow steel (E= 30,000ksi) tube (1) with an outside diameter of 2.75in. and a wall thickness of 0.25in. is fastened to a solid aluminum (E= 10,000 ksi) rod (2) that has a 2in. diameter and a solid 1.375in. diameter aluminum rod (3). The bar is loaded as shown in the figure. Determine (a) the change in length of steel tube (1); (b) the deflection of joint D with respect to the fixed support A. (c) the maximum normal stress in the entire axial assembly.
Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in. Segment BC is a solid rod of diameter d2. The average normal stresses must not exceed 3400 psi in rod AB and 6500 in rod BC, respectively. Use P1 = 3,650 lb. and P2 = 5,550 lb. a. Determine the smallest allowable value of d1 (in inches). Round-off to 2-decimal places. b. Determine the smallest allowable value of d2 (in inches). Round-off to 2-decimal places.
The constructed shaft is composed of a tube AB and a solid bar BC. The tube has an inner diameter of 20 mm and an outer diameter of 28 mm. The bar has a diameter of 12 mm. Determine the average normal stress at points D and E and identify whether the points are in compression or tension.answer:σD = -13.26 Mpa (compression) σE = 70.74 Mpa (traction)
The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft ( D = 2” and d = 0.75” ). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12 x 106 psi, 4 x 106 psi, and 6 x 106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the bronze shaft
The d = 12-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 10 mm. The rod head has a diameter of a = 29 mm, and the head has a thickness of t = 12 mm. If the normal stress produced in the rod by load P is 100 MPa, determine(a) the bearing stress acting between the support plate and the rod head.(b) the average shear stress produced in the rod head.(c) the punching shear stress produced in the support plate by the rod head. Calculate the cross-sectional area of the rod.Answer: Arod = mm2 Calculate the tension force in the rod.Answer: Frod = N Calculate the contact area between the support plate and the rod head.Answer: Acontact = mm2 Calculate the bearing stress between the support plate and the rod head.Answer: σb = MPa Calculate the area subjected to shear stress in the rod head.Answer: AV-rod head = mm2…
STRENGTH OF MATERIALS (NO LONG EXPLANATION NEEDED) PLEASE WITH FBD! RATE WILL BE GIVEN For the given system below, rods A and B support the rigid bar, pinned at O, as it is subjected to load P = 40 kN. The rods are identical except for their lengths. Find the (a) stress in rod A if its cross-sectional is 300mm2 (b) If rod A elongates by 2mm, how much is the elongation of rod B?
For the beam shown, determine the support reactions and draw the stress diagrams.shear and bending moment. EI is constant. Use the force method. I have a correct answer, it is: VA = 44.3 kN (↑); HA = 0 kN; MA = 34.3 kN.m (counterclockwise); VB = 38 kN (↑). I don't know how to get to this result, please show me how to get there step by step
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. If P = 75 kN, determine the following:a. Stress in the bronze segment.b. Stress in the aluminum segment.c. Stress in the steel segment.