Q1) (A) Two solid circular cross-section bar as shown in the Figure. If the stress in left portion is limited to 150 MN/m2, detemine the diameter of the left portion(D). Find also the length of the right portion(a) if the total elongation of the bar is to be 0.2mm. Young's modulus is E = 210 GN/m2. (B) If, in order to reduce weight whilst keeping the external diameter constant, the left portion is bored axially to produce a cylinder of uniform thickness, whatis the maximum diameter of bore possible given that the maximum allowable stress of the left portion is 180 MN/m2? The load can be assumed to remain constant at 160 kN. 0.03 m diameter 160 kN E D 160 kN a 0.4 m

Q1) (A) Two solid circular cross-section bar as shown in the Figure. If the stress in left portion is limited to 150 MN/m2, detemine the diameter of the left portion(D). Find also the length of the right portion(a) if the total elongation of the bar is to be 0.2mm. Young's modulus is E = 210 GN/m2. (B) If, in order to reduce weight whilst keeping the external diameter constant, the left portion is bored axially to produce a cylinder of uniform thickness, whatis the maximum diameter of bore possible given that the maximum allowable stress of the left portion is 180 MN/m2? The load can be assumed to remain constant at 160 kN. 0.03 m diameter 160 kN E D 160 kN a 0.4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two solid cylindrical rods support a load of P = 25 kN as shown. Rod (1) has a diameter of 13 mm, and the diameter of rod (2) is 12 mm. Determine the axial stress in rod (1).
In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa. Neglect the weight of the bar AB.
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb>ft2, determine the state of stress at points C and D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe.
13) Diameter of the solid shaft AB is 130 mm. Determine the maximum shear stress in the solid shaft AB.
5.2.2 The thin-walled tube is used as a beam to support the uniformly distributed load of intensity w0. (a) Find the largest allowable value of w0 based on the allowable stress in bending of 100 MPa. (b) Compute the corresponding maximum shear stress in the beam.
The system shown in the figure has an acceleration of 0.5 m / s^2. Kinetic friction between blocks and surface that the coefficients are the same for both inclined planes accepting that a) the kinetic coefficient of friction b) in the rope find the stress
The column in the figure is under the effect of a load of P = 16 kN. Find the stress at point A according to the given?
Draw the normal stress distribution in the section, given that a compressive force of P=20 kN is applied to the anode of the section given in the figure.
a) Determine the zero-effort frame by justifying with a table asfollow Joint in equilibrium Nul stress frame .
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 532 mm2 and P= 35.29 kN. Round off the final answer to four decimal places.
Figure Q3 (a) shows a cantilevered beam ABC carrying a pure moment of M kN.m at point B. Thecross-sectional area of the beam is shown in Figure Q3 (b). The yield stress of the material is 250 MPa and the material is assumed to behave linearly elastic-perfectly plastic.a) Where is the critical location for the beam and give ONLY ONE (1) reasonb) Determine the moment to initiate yielding in the cross-section of the beamc) Find the value of M that can cause plastic collapse (fully plastic) in the cross-section of the beamat the critical location and sketch the variation of stressd) If the TOTAL DEPTH of the plastic zone to be 20 mm at the critical location, WITHOUT ANYCALCULATION, sketch the variation of stress.
Determine the normal stress at segment CD. The cross-sectional area of bar ABCD is 600 mm^2.