Two weightless bars pinned together as shown, supports a load of 350 KN. Determine the forces acting along bars AB and AC that maintain equilibrium of pin A. Also, determine its stresses in Mpa if the cross- sectional area for both bars are 1000 sq. mm. Determine the values of 8 and a. 키 2m 커 8m C 4m 8m

Two weightless bars pinned together as shown, supports a load of 350 KN. Determine the forces acting along bars AB and AC that maintain equilibrium of pin A. Also, determine its stresses in Mpa if the cross- sectional area for both bars are 1000 sq. mm. Determine the values of 8 and a. 키 2m 커 8m C 4m 8m

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 56P: Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0...

See similar textbooks

Similar questions

Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
Suppose the weight of the drawbridge in Figure 9.34 is supported entirely by its hinges and the opposite shore, so that its cables are slack. (a) What fraction of the weight is supported by the opposite shore if the point of support is directly beneath the cable attachments? (b) What is the direction and magnitude of the force the hinges exert on the bridge under these circumstances? The mass of the bridge is 2500 kg.
The pole shown below is at a 90.0 bend in a power line and is therefore subjected to more shear force than poles in strsight part of the line. The tension in each line is 4.00104N , at the angles shown. The pole is 15.0 m tall, has an 18.0 cm diameter, and can be considered to have half the strength of hardwood. (a) Calculate the compression of the pole. (b) Find how much it bends and in what direction. (c) Find the tension in a guy wire used to keep the pole straight if it attached to the top of the pole at an angle of 30.0 with the vertical. The guy wire is in the opposite direction of the bend.
Explain the need for tall towers on a suspension bridge to ensure stable equilibrium.
A vertebra is subjected to a shearing force of 500 N. Find the shear deformation, taking the vertebra to be a cylinder 3.00 cm high and 4.00 cm in diameter.
A disk between vertebrae in the spine is subjected to a shearing force of 600.0N . Find its shear deformation, using the shear modulus of 1.0109N/m2 . The disk is equivalent to a solid cylinder 0.700cm high and 4.00cm in diameter.
Bone has a Youngs modulus of 18 109 Pa. Under compression, it can will island a stress or about 160 106 Pa before breaking. Assume that a femur (thigh bone) is 0.50 m long, and calculate the amount of compression this bone can withstand before breaking.
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
A 15.0-in uniform ladder weighing 500 N rests against frictionless wall. The ladder makes a 60.0 angle ESI with the horizontal, (a) Find the horizontal and vertical forces the ground exerts on the base of the ladder when an 800-N firelighter has climbed 4.00 m along the ladder from the bottom, (b) If the ladder is just on the verge of slipping when the firefighter is 9.00 m from the bottom, what is the coefficient of static friction between ladder and ground?
What Is Static Equilibrium? Problems 13 are grouped. 1. C A ball is attached to a strong, lightweight rod (Fig. P14.1). The rod is supported by a horizontal pin near the top. The ball is at rest. Is the ball in static equilibrium? If not, why not? If so, which type of equilibrium is itstable, unstable, or neutral? Hint: What would happen if you displaced the ball slightly? FIGURE P14.1
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?