Answered: Uniaxial yield stress of a material is…

Engineering

Mechanical Engineering

Uniaxial yield stress of a material is 420 MPa Determine shear yield stress using Von Mises criteria.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.7P: -7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5...

See similar textbooks

Related questions

Q: In the system shown, a force P(t) is applied at C. Bar ABCD is of negligible mass. Determine: The…

Q: Q1) Air flows over a plane wall at a Mach number 3.5, the pressure in the flow being 100kpa. The…

Q: The specific steam

A: Given; Enthalpy at entry and exit is; h1=3159 kJ/kg h2=2187 kJ/kg Specific pump work=2…

Q: What is the cycle efficency?

A: The given cycle is diesel cycle . For finding thermal efficiency of cycle we need to find…

Q: The general energy equation is . For the picture blow, select the simplified the form of the general…

Q: A rigid bar, hinged at one end, is supported by two identical springs as shown in Fig. P-349. Each…

Q: Q1-A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box…

Q: I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal…

Q: non-Newtonian fluid is modelled by the equation of T = K () where K=0.05 Pa.sº.. It ows through a…

Q: Find force applied Work done=101.232 J Dispalcement-20 m

Q: Air enters an adiabatic drier at 6 m/s through a 2m diameter duct at 29 ºC dry bulb and 22 ºC wet…

Q: 17 A gas occupies 0.2 cu. m. at 65.8 kPa & 20°C. Find its volume at STP. * 1.210 cu m 12.10 cu m O…

Q: The questions is this: A 5000-lb. gear box is provided with a steel (as rolled B1113) eyebolt for…

A: Given DataFe=5000lbB1113 are using Using the table Screw and fastening

Q: DF=20.032 N d=12m 3 Find work done.

A: Given data : Displacement=d Force=F Required : Work done

Q: Q3-Blocks A and B have a mass of 7 kg and 10 kg, respectively, and there are pulleys at C and D.…

Q: Air is to be heated by passing it over a bank of 3 m long tubes inside which steam is condensing at…

Q: A, B, C and D are four masses carried by a rotating shaft, the masses and eccentricity at B and C…

Q: 2. When s = 0.6 m, the spring is unstretched and the 10-kg block has a speed of 5 m/s down the…

Q: The minimum time (in days) for completion of the project

A: Given; A project consists of 7 activities. Network along with the time durations for various…

Q: Determine the safe tensile load for bolts of (a)M 17and (b) M 26. Assume that the bolts are not…

A: Given Tensile stress = 305 MPa Diameter, M17, D = 17 mm M26, d = 26 mm…

Q: Thank you for the answer. but sir/ma'am it's kind of blurry can you do something about it if no,…

Q: 29. Steam at 1.4 MPa, 300 deg C expand isentropically until it bevomes saturated. Determine a)delta…

A: As per our company guidelines we are supposed to answer only first 3 sub parts in case of multiple…

Q: -) The temperature distribution across a wall of an aluminium cylin- der block, 4 mm thick at a…

Q: Q2 - Replace the distributed loading with an equivalent resultant force, and specify its location on…

Q: please send handwritten solution Q4 part d e f

Q: The temperature distribution across a wall of an aluminium cylin der block, 4 mm thick at a certain…

Q: Q2) A piston/cylinder has ammonia at 1600 kPa, 100°C with a volume of 0.1 m3. The piston is loaded…

Q: j) k) Solve for x (x-coordinate of the composite area's Centroid) Solve for y(y-coordinate of the…

A: (j) Write the x-coordinate of centroid for each shape. x1=200-4r3π=200-42003π=115.12…

Q: A 5000-lb. gear box is provided with a steel (as rolled B1113) eyebolt for use in moving it. What…

Q: would the normal force of B just have Nb=W-Psin36

A: Normal force at B , Take moment about point A then you will get the normal force at B in terms fo…

Q: 3=DF=20-032 N d=12m Find work done.

Q: Material Strengths: Fy = 248 MPa, Fu = 400 MPa Method: Use ASD. A single angle L127X89X19 is welded…

A: Welding is a manufacturing method for joining materials, mainly metals or thermoplastics, by melting…

Q: Given data. Stress=202 N/mm² Area = 3 mm? Find Force.

Q: 10. Figure 6 shows two cables AB and BC supporting a 1500 N load. A C 2.50 m 2.25 m 3.00 m 1500 N…

A: Find the length of Ab and BC also find force in AB and BC

Q: Q'/ If the fitting symbol between the shaft and hole is (8G7/h6), find? 1-The upper and lower…

Q: 3) Determine the moment of inertia of the composite area about the x and y axes

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: Given data Reduction ratio = 2.32 Input torque= 100N-m Input speed = 3000rpm Efficiency = 98% Find…

Q: A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box and…

Q: Think about how the concepts of dynamic and materialised views compare and contrast with one…

A: INTRODUCTION: The way views and materialized views take up storage space is one of the most…

Q: what is the cost of that heat loss to the home owner for 10hours if the cost of electricity is PHP…

A: Given Time, t = 10 hours Rate, R = PHP 0.45/kWh Heat loss, Q = 2.46 kJ/s Find…

Q: A boiler produces 25 kg/s of steam at 3 MPa and 600 °C, cools the condenser with seawater so that…

A: Given:m=25 kg/sP1=3 MPaT1=600°CT2=45°CP3=500 KPaT3=400°CP4=Patm=101.325 KPa

Q: An unknown mass m is attached to two identical springs. Each spring has a stiffness k = 10 N/m and…

A: Given Stiffness, k = 10 N/m Amplitude, A = 3 m Length, L = 4 m Find Acceleration, a Mass, m…

Q: 6. (a) The temperature distribution across a wall of an aluminium cylin- der block, 4 mm thick at a…

Q: As shown in the picture blew, a pump can deliver volume flow rate of of water through a vertical…

Q: m) What are the centroidal moments of inertia: Ix2, Iy2, Ix4, and Iy4, of shape 2 and 4? n) What are…

A: Given questions: m) What are the centroidal moments of inertia: Ix2, Iy2, Ix4, and Iy4, of shape 2…

Q: A resistance-capacitance relaxation circuit is used in an electrical discharge machining process.…

Q: A steel rim, with a mean diameter of 1 m, rotates at 1 000 r/min. Determine the circumferential…

Q: Indicate the number of pieces in Image 1. For example, in the image with a number 2, there are 5…

A: The number of pieces in the given image

Q: Determine other F = 0.02 N A = 2m²

A: Given data : Force=F Area=A To find : Stress

Q: SIETER OF THE =::=:: 1575) 조선왕료 foll ROLLO moros.biqui FOR-ONER/STANE POL SAM FOR / TOT Roug 0 2 규…

A: The number of pieces in the given image

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

Uniaxial yield stress of a material is 420 MPa
Determine shear yield stress using Von Mises
criteria.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A spherical steel pressure vessel (diameter 500 mm, thickness 10 mm) is coated with brittle lacquer that cracks when the strain reaches 150 X 10~ (see figure). (a) What internal pressure p will cause the lacquer to develop cracks? (Assume E = 205 GPa and v = 0.30.) (b) If the strain is measured at 125 x 10-6, what is the internal pressure at that point?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.
A W 8 × 28 beam of a length 10 ft is held between immoveable supports. The beam has a modulus of elasticity E = 29,000 ksi and coefficient of thermal expansion a = 6.5 ×10-6 /?. If the temperature of the beam is raised uniformly by an amount AT = 20°F, calculate the thermal stress aTin the beam.
Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.