unsigned int adc; void main() { ADCON1 = ex80; OXFF; // PORTA is input TRISA TRISC = 8X3F; // Pins RC7, RC6 are outputs TRISB = e; // PORTB is output do { ADC_Read (1); // Get 10-bit results of AD conversion //of channel 1 adc PORTB adc; // Send lower 8 bits to PORTB PORTC = adc >> 2; // Send 2 most significant //bits to RC7, RC } while(1);

unsigned int adc; void main() { ADCON1 = ex80; OXFF; // PORTA is input TRISA TRISC = 8X3F; // Pins RC7, RC6 are outputs TRISB = e; // PORTB is output do { ADC_Read (1); // Get 10-bit results of AD conversion //of channel 1 adc PORTB adc; // Send lower 8 bits to PORTB PORTC = adc >> 2; // Send 2 most significant //bits to RC7, RC } while(1);

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 10VE

See similar textbooks

Similar questions

A(n) _____ operation transforms a 0 bit value to 1 and a 1 bit value to 0.
Write a program that acquires data from a data source and calculates and displays the Discrete FourierTransform associated with that data. In this case, the Arduino will generate a signal, that is sampled by the ADC and then sent to the computerover the serial port. The Arduino code is : int lookup_index = 0; #define SIN_FREQ 100 long sin_freq = SIN_FREQ; #define LOOKUP_ARRAY_SIZE 128UL #define PWM_RESOLUTION 8 #if PWM_RESOLUTION <= 8 #define PWM_t uint8_t #else #define PWM_t uint16_t #endif PWM_t *lookup_array; // lookup array for sin(2pi f t) PWM_t lookup_array1[LOOKUP_ARRAY_SIZE] = { 127, 133, 139, 146, 152, 158, 164, 170, 176, 181, 187, 192, 198, 203, 208, 212, 217, 221, 225, 229, 233, 236, 239, 242, 244, 247, 249, 250, 252, 253, 253, 254, 254, 254, 253, 253, 252, 250, 249, 247, 244, 242, 239, 236, 233, 229, 225, 221, 217, 212, 208, 203, 198, 192, 187, 181, 176, 170, 164, 158, 152, 146, 139, 133, 127, 121, 115, 108, 102, 96, 90, 84, 78, 73, 67, 62,…
S-boxes in DES map a. 4 to 6 bits b. 6 to 4 bits c. 4 to 2 bits d. 2 to 4 bits
WAP program creates a BitArray of five Byte values (1,2,3,4,5) anddisplays each byte in its proper binary form:
Design 4 bit left/right rotation circuit that specifies the number of bits in the rotation by a 2-bit word Ro_n, and the direction of rotation by a single bit R/L such that R/L = 1 denotes a right rotation and R/L = 0 is a left rotation.
Bit rate is the product of ... a. bit frequency and sampling frequency b. sampling and quantization ratios c. bit depth and quantization error d. bit depth and bit frequency e. sampling frequency and bit depth
LIST P = 16F877AUsing INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the microprocessor code that enables the fan to operate at 80% if the button on the 5th bit is pressed, and 30% if the button on the third bit is pressed.
In ___________ there is always a transition at the middle of the bit, but the bit values are determined at the beginning of the bit. If the next bit is 0, there is a transition; if the next bit is 1, there is none.
One way to calculate the parity of a 32-bit number in EAX is to use a loop thatshifts each bit into the Carry flag and accumulates a count of the number of times the Carryflag was set. Write a code that does this, and set the Parity flag accordingly
Build C program to perform task below. Design its circuit in Proteus. State your observations.a) Make Port D produce 5V. Use bit addressable instructions.b) Make pin RB7, RB5, RB3 and RB1 ON and other Port B pins OFF. Use byte addressableinstruction.c) Make RE0, RA1, RB2, RC3 and RD4 HIGH.result discussion conclusion
In the hamming code C (7, 4), three redundant bits are generated as follows:0 2 1 0 r = a ⊕ a ⊕ a1 3 2 1 r = a ⊕ a ⊕ a2 3 1 0 r = a ⊕ a ⊕ a
The decoder translates the binary value into a decimal value. The following figure shows a block diagram of 3-bit binary decoder. The 3-to-8 decoder has three inputs A2, A1 and A0, and eight outputs, i.e. Y7 through Y0. Answer the following questions. (Note: You should show all the steps) 1. If the inputs A2 A1 A0 = 0 0 0, what are the outputs Y7 – Y0? 2. If the inputs A2 A1 A0 = 1 0 0, what are the outputs Y7 – Y0?