Use the graphical method to construct the shear-force diagram and identify the magnitude of the largest shear force (consider both positive and negative). The ground reactions are provided. P = 58 kN w=14 kN/m L=3m A₂ = 45.67 kN Dy=54.33 kN L B L W L

Use the graphical method to construct the shear-force diagram and identify the magnitude of the largest shear force (consider both positive and negative). The ground reactions are provided. P = 58 kN w=14 kN/m L=3m A₂ = 45.67 kN Dy=54.33 kN L B L W L

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.12P: Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in...

See similar textbooks

Related questions

Q: In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at B and…

Q: Find the depth of a point below water surface in sea where the pressure intensity is 100.55 kN/m².…

Q: 2. Consider the following compound pendulum, which consists of a thin rod attached to a pivot point…

A: For solution refer below images.

Q: 7)Laminar flow (a) takes place at very low velocities. (b) does not take

A: given statement : Laminar flow ........ place at very low velocities a) takes b) does not take

Q: a. By using horizontal element, determine the y-centroid for the shaded area shown in Figure la. Let…

A: Given is the equation of curve and dimensions. Required: Y centroid using horizontal element.

Q: Propal alcohol (C3H7OH) is burned with 50 percent excess air. Write the balanced reaction equation…

A: The air-fuel ratio is the air-mass-to-fuel mass ratio present in the gasoline fuel combustion…

Q: 3.12 (USCS Units) A low-carbon steel tensile specimen with starting gage length = 2.0 in and…

Q: Question 17 Trouver la hauteur de la section et une de deux réactions (Ay) pour la poutre en bois…

Q: (2) 11) The maximum velocity in a circular pipe when flow is laminar occurs at (b) the center of the…

A: Find where is the maximum velocity occur in laminar flow in circular pipe .

Q: Determine the extension (m) of the whole system shown ik1-15.42 Nm, 42-27.49 Nm, 43-363 7.83 Nm, and…

Q: An overhead 25-m-long, uninsulated industrial steam pipe of 162-mm diameter is routed through a…

A: The given data in the problem is shown in the following attached image:

Q: Heat flows through a wall of a house at a steady-state on a day when the temperature of the outdoor…

A: GivenTo=2oC=2+273=275KTi=27oC=27+273=300K

Q: (a) the strains in these directions, (b) the changes in dimensions, (c) the volumetric strain and…

Q: A spherical container holding a hot fluid at 500 K and having an outer diameter of 0.5 m is…

Q: Question 1 Estimate the size of cooling equipment (in kW), that is needed for a new post office…

Q: The curved pipe has a radius of 5 ft. Figure 60 1001 S Part A If a force of F=75 lb acts at its end…

Q: The white petrolatum has specific gravity of 0.850, what is the weight of this substance meeded to…

A: Given:Specific gravity of white petroleum is 0.852 fluid ounce=59.147 ml

Q: What is the Temperature of 02 gas if it starts at 45oC and a volume of 7L and ends at a volume of…

Q: 12) The unit of the constant(H) in the Bernoulli's equation is m.kg, Is kg, (a) (b) (c) m.kg,/ kg,…

A: Below is the detailed answer for the unit of constant in the Bernoulli equation.

Q: The two aluminum rods AB and AC have diameters of 10 mm and 8 mm, respectively. (Figure 1) Figure…

A: GivendAB=10mmdAC=8mmσallow=150 MPa

Q: A tensile test specimen of 1045 hot-rolled steel having a diameter of 0.505 in. and a gage length of…

A: Givend=0.505 inL=2 inoffset =0.20%

Q: Problem 3: A person runs outward from the center of a carousel at a constant speed () of 8.4 ft/s,…

A: The given information in the problem is shown in the following attached image:

Q: A tension test was performed on a steel specimen having an original diameter of 0.503 in. and gauge…

Q: A flanged bolt coupling has ten 16-mm diameter steel bolts on 800 mm diameter bolt circle a nd six…

A: The given information in the problem is shown in the following attached image:

Q: A gear set consists of a full depth 50-tooth gear driven by a 25- tooth pinion. The module of the…

Q: 1)The gravity at a location is 5 ms. The density of fluid was 2000 kg/m³. The pressure exerted by a…

A: According to the given data (1) The gravity at any point = g'=5m/s2 Density=ρ=2000kg/m3 Height of…

Q: Water enters a perforated irrigation pipe (Length L, diameter D) with a uniform velocity Uin=10m/s.…

A: The pipe diameter is D. The inlet velocity of water is Uin=10 m/s. The outer velocity is Uout=80…

Q: Please solve the centroidal Ixc, centroidal Iyc, Ix and Iy of the attached figure. please help ASAP

Q: 6. The figure below represents a time response of a control system. y() I 0.63 0 What is it? a)…

A: Solution: Given Data: A time response of a control system: To Find:

Q: velocity A ball is shot Vertically into the air @ a of 193.20 81/sec. After 4 secs another ball is…

Q: The bolt is subjected to the force F, which has components acting along the x, y, z axes as shown in…

Q: 1)The gravity at a location is 5 m/s². The density of fluid was 2000 kg/m³. The pressure exerted by…

Q: Large hydroturbines achieve overall efficiencies above 95%, while the best efficiency of large…

A: The reason of large hydro turbines achieve overall efficiencies more than large pumps are given…

Q: he gauge readings at A and B in Fig. 2.51

A: From the figure, Assuming the vapour pressure of mercury and pressure due to short column of air to…

Q: augnol tobubbA 80 0.005W/mm 950 S02 Figure 2) Op 9001 W/mm Figure 1) The femur bone is maintained…

A: The load distributed W is 637.65 N. The total length of AB is 225 mm (approx).

Q: For each of the following problems, (a) determine whether the links can actually form a mecha- nism…

A: Solution: Given Data: Lo=1.5L1=4L2=2L3=3.5 To Find: (a) Is a mechanism possible with the given…

Q: Lily weighs 70 kg and has a total foot imprint area of 400 cm². Lily wishes to walk on the snow, but…

Q: 1. A U-tube mercury differential manometer is used to measure the difference of pressure between…

A: Given data The manometer reading = 250mm Find the pressure difference between inlet and throat .

Q: Nitrogen flows at 1000 kg/h into a compressor at 1 bar and 300 K and leaves at 5 bar and 420 K,…

A: GivenmN=1000 kg/hP1=1barT1=300KP2=5barT2=420Kfor watermw=1400 kg/hTw1=300KTw2=320K

Q: A child's balloon is a sphere 0.9 ft in diameter. The balloon is filled with helium (p = 0.014…

Q: The pins at C and A are in double shear, and the pin at B is in single shear. All pins have a…

Q: 1.) Determine the mechanical advantage for the following scenario: 111in 16in

A: Solution: Given Data: To Find: The mechanical advantage.

Q: 17-130 Steam in a heating system flows through tubes whose outer diameter is 3 cm and whose walls…

Q: Of the following, the SHORTEST is ______ a. 1.2 miles b. 1610 meters c. 63350 inches d. 1060…

Q: A car is moving on a curved horizontal road of radius 100 m with a speed of 20 m/s. The rotating…

A: Given:ω=100 rad/s I=10 kg-m2r=100 mv=20 m/s

Q: Carnot cycle heat pump utilizes R-134a as the working fluid. Heat is transferred from the fluid at…

A: Given:Refrigerant=R134aCondenser temperature, Tc=100oFEvaporator temperature, Te=20oFFind:a…

Q: The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. Figure 4 ft 3 f 1 of 1 >…

Q: PROBLEM 2 Determine the force in each member of the truss and state if the members are in tension or…

Q: -114. Determine the magnitude of the projection of F₁ along the line of action of F2. 2-115.…

A: Given data F1= 30(lb) and F2=25(lb) Find the magnitude of the projection of F1 along the line of…

Q: The horizontal roof of a building has an emittance of 0.9. Air temperature is 1oC on a clear night.…

A: Conduction and convection heat transfer needed the use of a material medium to transfer heat from…

Question

use kN as final answer

Use the graphical method to construct the shear-force diagram and identify the magnitude of the largest shear force (consider both
positive and negative). The ground reactions are provided.
P = 58 kN
w=14 kN/m
L=3m
A₂ = 45.67 kN
Dy=54.33 kN
L
B
L
W
L

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
The strains for an element of material in plane strain (see figure) are as follows: x = 480 ×10-6. y = 140 × l0-6, and xy = —350 x 10”. Determine the principals strains and maximum shear strains, and show these strains on sketches of properly oriented elements.
Use the graphical method to construct the shear-force diagram and identify the magnitude of the largest shear force (consider both positive and negative). The ground reactions at the wall of the cantilever are provided. L₁= 14.75 ft L₂ = 7.75 ft Vc = 91.50 kips Mc = 706.4375 kip-ft 20 kips 6 kips/ft L₁ 103.50 kips 68.50 kips 91.50 kips O 79.50 kips O 114.50 kips 70 kips BO 12 kips/ft L2 O Vc Mc
Use the graphical method to construct the shear-force diagram and identify the magnitude of the largest shear force (consider both positive and negative). The ground reactions at the wall of the cantilever are provided. L₁= 14.00 ft L2= 7.75 ft Vc = 87.00 kips Mc = 621.875 kip-ft 20 kips 6 kips/ft L₁ 64.00 kips 99.00 kips 110.00 kips 87.00 kips O 75.00 kips 70 kips B 12 kips/ft L2 Vc Mc
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
Figure below shows the bar with three equal elements. Use the finite element method and calculate: 2.1 the global stiffness matrix 2.2 the displacement on node 2, 3, 4 2.3 the Strain in each element 2.4 the stresses in each element using Hook's law and compare with theoretical stresses (o=F/A) (1) (2) (3) -50 N 10 mm 10 mm 10 mm A1=50 mm? A2=20 mm? A:=10 mm? E=200 GPa
A very thick structure is subjected to certain traction boundary conditions on its surface. The cross-section and the applied load do not vary with the z-coordinate. The following stress function is proposed for this problem: -y p(x,y) = Sin (x) (A x²e + B e") (i) use the biharmonic equation to find restrictions, if any, on values of A and B (ii) calculate all stress components (iii) calculate all strain components in terms of A, B, and C as well as the Young modulus and Poisson's ratio E and y, respectively. (iv) check that the equilibrium equations are satisfied (v) determine the traction boundary conditions at x =± a and y=+b
The state of strain at the point has components of €g = 180(10 6). €y = -100(10 6) Submit Previous Answers and All attempts used; correct answer displayed Yay = -200(10-6). Part B Figure < 1 of 1 Specify the orientation of the element. Enter your answers numerically separated by a comma. Hν ΑΣφ It vec (6,)1, (0,)2 = Submit Request Answer Part C
A square post which is made up of two parts is glued atplane ABCD with the angle α = 30° with the vertical.Allowable compressive stress @ glue = 5.2 MPaAllowable shearing stress = 3.5 MPaP = 36 kN. 1. What is the minimum post dimension, w (mm), withoutexceeding the allowable shearing stress at the glue? 2. What is the minimum post dimension, w (mm), withoutexceeding the allowable compressive stress at the glue? 3. What angle, α, will give the maximum shearing stress? with brief explanation each part
Problem 3. As shown in the Figure below, please determine the internal force in the middle of AB, with the given data: OA-15 cm, OB-30 cm, OC-60 cm. W=40N, Wo=60N. F=1214N, B-10°, FM=1236 N, and 8=15%. Fj B FM W Wo 4
Question 3 Show that the following function o may be used as an Airy stress function $ = Ax? + Ba²y+ Cry Evaluate A, B and C for the rectangle shown in Figure Q3: (1) there are no external loads for any kind applied along KN; (2) along KL there is a uniform normal load p; (3) and along MN there is no normal load; (4) along KL, LM and MN there are shear stresses (but none along KN). Make a neat sketch of the stresses along the boundary KLMN. y N M Thickness=1 b p per unit length a
Solve following the problems below and show your complete, systematic and neat solution. Upload your solution with one PDF file. 1. For the beam shown, a. determine the maximum flexural stresses in compression ant tension. b. determine the flexural stress of the fiber located at 3m from the left support and 50 mm above the bottom 18 kN/m 300 mm 6 kN/m 20 mm 27 kNm 22 2m 2m 3 m +m 15 mm - - 50 mm 360 mm 20 mm