In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining Band D, determine the allowable load P if an overall factor of safety of 2.6 is desired. Top view 8 mm. A -200 mm- B DO -180 mm- The allowable load P is 20 mm Front view 12 mm C P KN. t 8 mm- 4. 12 mm. 1 B -8 mm D the Side view

In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining Band D, determine the allowable load P if an overall factor of safety of 2.6 is desired. Top view 8 mm. A -200 mm- B DO -180 mm- The allowable load P is 20 mm Front view 12 mm C P KN. t 8 mm- 4. 12 mm. 1 B -8 mm D the Side view

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The structure is used to support a distributed load of w = 15 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3,080 mm^2. The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C.
Two wooden planks, each 7/8 in thick and 6in wide, are joined by the glued mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 120psi, determine the smallest allowable length d of the cuts if the joint is to withstand an axial load of magnitude P=1200-lb. Note: Seven surfaces carry the load, P=1200-lb
In the structure shown, an 8-mm diameter pin is used at A, and 12- mm diameter pins are used at B and D. Knowing that the ultimate shearing stresses is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 3.0 is desired.
' Three piates are joined with a 12-mm diameter pin as shown beiow. Determine the maximum load p that can be transmitted by the joint if the maximum bearing stress between a plate and the pin must be limited to 650 MPa .
In the structure shown, an 8-mm diameter pin is used at A, and 12-mm diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor ofsafety of 3.0 is desired.
In the steel structure shown, a 6-mm-diameter pin is used at C and10-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Knowing that a factor of safety of 3.0 is desired,determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes.
Each of the two vertical links CF connecting the two horizontal members AD and EG has a 10x40-mm uniform rectangular cross section and is made of a steel with an ultimate strength in tension of 400 MPa,while each of the pins at C and F has a 20-mm diameter and is made of a steel with an ultimate strength in shear of 150 MPa. Determine the overall factor of safety for the links CF and the pins connecting them to the horizontal members.
The two parts of the eyebar are connected with two 1/2-in.-diameter bolts (one on each side). Specification for the bolt require that the axial tensile stress not exceed 12.0 ksi and that the shearing stress not exceed 8.0 ksi. Determine the maximum load P that can be applied to the eyebar without exceeding either specification
In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 350 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. The largest load P that can be applied at A is kN.
The eyelet (figure) is used to support a load of 3000 kgf. Determine its diameter d, and the required thickness h, so that the washer does not penetrate or shear the support. Knowing that the eyelet and washer must be made of 1020 steel, cold rolled, with a safety factor of 2.5, and the gap between the screw and the through hole must be 4mm, the steel used will be annealed and threadmachined, and the outer diameter of the washer will be 40mm.
The five-bolt connection shown must support an applied load of P = 214 kN. If the average shear stress in the bolts must be limited to 249 MPa, determine the minimum bolt diameter that may be used in the connection.
The lap joint shown is connected by three 16-mm diameter rivets. If the allowable stress for shear in rivets is 40 MPa and bearing between therivets and the plates is 60 MPa determine the safe load P.