Use the Principle of Superposition to determine the absolute value of total current, in milliamperes, through R, in the circuit below, given: E₁ = 31 V, E₂ = 24 V, and R₁ = 130 (Round your FINAL answer to a whole number.) ли E₁₁ || R₁ E₂ Click on the image to view a larger version of it. Answer: mA

Use the Principle of Superposition to determine the absolute value of total current, in milliamperes, through R, in the circuit below, given: E₁ = 31 V, E₂ = 24 V, and R₁ = 130 (Round your FINAL answer to a whole number.) ли E₁₁ || R₁ E₂ Click on the image to view a larger version of it. Answer: mA

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 10PP: In an R-L parallel circuit, ET=240 volts, R=560, and XL=330. Find apparent power.

See similar textbooks

Similar questions

"NODAL VOLTAGE ANALYSIS" Please Find the Vo Using NODAL VOLTAGE ANALYSIS thankyou very much! I've included a cicruit app to check if your answer was correct and close to the value of currents and voltages which is 0.5V thankyou! I've been testing simple circuits to practice problems using different theorems,I appreciate you very much Thankyou!
Given: R= 482 ohms, L= 0.8H, C= 30 microFarradInstruction: Solve for Vc, IL, VR. Provide detailed solution for it. See the attached picture for the circuit diagram.
"MILLMAN’S THEOREM" Please Find the Vo Using MILLMAN’S THEOREM thankyou very much! I've included a cicruit app to check if your answer was correct and close to the value of currents and voltages which is 0.5V thankyou! I've been testing simple circuits to practice problems using different theorems,I appreciate you very much Thankyou!
(Basic Electrical Engineering) When connected to a 220V, 50Hz supply and impedance coil circuit takes 5 A, but this current falls to 4.4 A when a 10-ohm resistor is added in series. Find the inductance of the coil. Show complete solution and limit your answer into three decimal places.
"NORTON'S THEOREM" Please Find the Vo Using NORTONS’S THEOREM thankyou very much! I've included a cicruit app to check if your answer was correct and close to the value of currents and voltages which is 0.5V thankyou! I've been testing simple circuits to practice problems using different theorems,I appreciate you very much Thankyou!
"SUPERPOSITION THEOREM" Please Find the Vo Using SUPERPOSITION THEOREM thankyou very much! I've included a cicruit app to check if your answer was correct and close to the value of currents and voltages which is 0.5V thankyou! I've been testing simple circuits to practice problems using different theorems,I appreciate you very much Thankyou!
The following are the readings taken while conducting an experiment on a wind turbine. what will be the value of open circuit voltage, if the short circuit current is 0.472 A, Maximum power point voltage is 5.32 V, Maximum power point current is 0.111 A and the fill factor is 0.599? Select one: a. 2080 mV b. 2.08 mV c. 8020 V d. 80.2 V
Write your complete solution.
Hey, A power grid is to be created in a city. There are several buildings and there are pairedconnections between the buildings. Not every building is connected to every other building. In particular, there may be buildings that are not connected to any other building.Based on the mentioned connections, a power grid is to be designed now. Therebystarting from a given building (the electricity factory), so that as many buildings as possible are in the network.as many buildings as possible are in the network.A power cable can be laid only between connected buildings and there will be exactlyone power cable is needed for a connection between two buildings. A building is in thepower grid if it can be reached from the power factory by one or more power cables. Specify an algorithm in pseudo code that, given buildings and connections, calculates a power gridthat satisfies the above properties with as few power cables as possible.Determine the running time of your algorithm and give a…
Can you please show the solution of the image below. Thanks!
Given a series circuit consisting of a DC voltage source, resistor, capacitor, inductor, and switch which closes at t=0. All elements are initially uncharged. If V=4 volts, R=64 Ohms, C=1/520 Farads, and L=8 Henries, Determine the circuit current (A,B,H,D): i(t)=Aexp(-Bt)sin(Ht+D) amps.
Short Problem: Given a parallel RLC circuit comprised of the following element: 97.19-ohm resistor, ideal inductor with reactance of 36.14 ohms; and a capacitor with reactance of 16.25 ohms. Compute for true power in watts given an ac voltage source of 100 cis 0 volts. Note: Follow this reminder carefully. Compute to the nearest 4 decimal places. No Scientific notation. Do not round off in the middle of calculation. Use stored values. Write the numerical values only. No units in your final answer. Spaces are not allowed. Excessive number of decimals as compared to the required number of decimals may result to an incorrect answer.