A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of 2.2 N/m2 to maintain this speed with using an oil of specific gravity 0.75. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates.

A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of 2.2 N/m2 to maintain this speed with using an oil of specific gravity 0.75. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.13P: 5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its...

See similar textbooks

Similar questions

Calculate the power required per meter of width of stream to force lubricating oil through the gap between two horizontal flat plates under the following conditions: Distance between plates, 6 mm Flow rate of oil per meter of width, 100 m3h Viscosity of oil, 25 cP Density of oil, 0.88 g/cm3 Length of plates, 3 m Assume that the plates are very wide in comparison with the distance between them and that end effects can be neglected.
A plate 0.05mm distance from a fixed plate moves at 1.25 m/s and required a force per unit area of 3 Pa to maintain this speed by using an oil of specific gravity 0.65. Find the dynamic viscosity in centipoise and kinematic viscosity in stokes of the fluid between the plates. Calculate the specific weight in kN/m³, density, and the specific gravity of a liquid having a volume of 662900 cm and weight of 55 kN
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3 Please.. explain more easy
Aiming a 1.69 in diameter garden hose straight up, forms a “bubbler fountain” that you could easily drink from (but you shouldn’t because of bacteria, etc.). The water flows out the hose and down the sides. If the water has a density of 63.1 lbm/ft^3 and a viscosity of 0.0119 g/cm*s, what is the thickness of the water film (df) (in cm) if the flow rate of water is 6.42 in^3/s? For simplicity, assume the film is thin enough that you can use rectangular coordinates.
please answer A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle β2 is 158° and the radial velocity at the outlet Cr2 is 4 m/s. Assuming radial flow at inlet, draw the theoretical outlet velocity diagram and calculate the various velocities and angles.( A)What is the theoretical head Ho, in meters, assuming that the circulatory flow coefficient η∞ = 1.,(B)In the preceding example; assume a deviation of 10° applied to β2 due to circulation after the modern theory. The flow is 30 lit/s. After drawing/illustrating the velocity diagram, find the theoretical head Ho, in meters, assuming radial flow at inlet, neglecting the deviation in inlet velocity diagram. (c)Assuming that the mechanical efficiency ηmech = 0.95, the hydraulic (or manometric) efficiency ηman = 0.8, find the required break horsepower to drive the pump.
A model of the Airbus 320 is tested in a wind tunnel using air at standard conditions. If the tunnel airspeed is 50m/s, calculate the water speed if the same model is to be tested in a water tunnel atdynamically similar conditions. Take mair=1.73 x 10-5Pa.s, mwater=10-3Pa.s, rair=1.225kg/m3 andrwater=1000 kg/m3.
When a person ice skates, the surface of the ice actuallymelts beneath the blades, so that he or she skates on a thinsheet of water between the blade and the ice.( a ) Find an expression for total friction force on the bottomof the blade as a function of skater velocity V , bladelength L , water thickness (between the blade and theice) h , water viscosity μ , and blade width W .( b ) Suppose an ice skater of total mass m is skatingalong at a constant speed of V 0 when she suddenlystands stiff with her skates pointed directly forward,allowing herself to coast to a stop. Neglecting frictiondue to air resistance, how far will she travelbefore she comes to a stop? (Remember, she iscoasting on two skate blades.) Give your answer forthe total distance traveled, x , as a function of V 0 , m ,L , h , μ , and W .( c ) Find x for the case where V 0 = 4.0 m/s, m = 100 kg,L = 30 cm, W = 5.0 mm, and h = 0.10 mm. Do youthink our assumption of negligible air resistance is agood one?
2. A fan discharges 265 cu.m/min of air through a duct of 92 cm in diameter against a static pressure of 0.022 m of water. The fluid density is 995 kg/cu.m., the air temperature is 29°C and the barometric pressure reading is 730 mm Hg. If the power input to the fan is measured 3.5 hp, what are the total and static fan efficiencies?
Oil (dynamic viscosity) between a block of mass M (5 kg) and the substrate(μ = 1.6 Pa.s), oil film thickness (h = 0.7 mm)). Block base surfaceIts area is given as A = 28 cm2. Block m (1kg weight) with a wire ropeIt depends on the mass. At time t = 0, mass m is released. According to these data;a) Find the viscous forces when the block moves with V = 1 m / s velocity.b) Derive an equation for the block velocity as a function of time (t).c) Plot the velocity-time variation for t = 0 and t = t.
A Pitot tube at a height of 3 m, measures wind velocity 5.3 m/s. What is the wind velocity at a height of 50 m? If the center of a 45 m diameter wind turbine is placed at 50 m, what is the maximum power this turbine may produce?
In a chemistry plant, through a horizontal smooth pipeline with a diameter of 0,3 m, a fluid with density and viscosity of 769 kg/m3 and 0,0007 Pa-s, respectively is flowing with a flow rate of 0,009 m3/s. Disregarding the pipe entrance effects and treating flow being steady, uniform and incompressible; a) Find the magnitude of mean velocity (in m/s). (Please use only 3 decimal digits.) b) Find Reynolds number. (Please do not use any decimal digit.) c) Find the magnitude of friction factor. (Please use 4 decimal digits.)