Truss Analysis (Statics of Rigid Bodies) Using method of joints, analyze the following figure if: h=5.25 ft, d=7 ft775lb775 lbD.775 lbh175 lb175 lbhAddd.dWhat is the value of force in member AB?What is the value of force in member AC?What is the value of force in member BC?What is the value of force in member BD?What is the value of force in member BE?What is the value of force in member CE?What is the value of force in member DF?What is the value of force in member DE?What is the value of force in member EF?What is the value of force in member EG?What is the value of force in member FG?What is the value of force in member FH?What is the value of force in member GH?

To find force in all members of the truss

Using method of joints, analyze the following figure if: h=5.25 ft, d=7 ft 775 Ib 775 lb D 775 lb 175 lb 175 lb C. ¡G d d d P at is the value of force in member AB? at is the value of force in member AC? at is the value of force in member BC? at is the value of force in member BD? at is the value of force in member BE? at is the value of force in member CE? at is the value of force in member DF? at is the value of force in member DE?

Using method of joints, analyze the following figure if: h=5.25 ft, d=7 ft 775 Ib 775 lb D 775 lb 175 lb 175 lb C. ¡G d d d P at is the value of force in member AB? at is the value of force in member AC? at is the value of force in member BC? at is the value of force in member BD? at is the value of force in member BE? at is the value of force in member CE? at is the value of force in member DF? at is the value of force in member DE?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two forces FA =168 lb and FB =265 lb are acting on the bracket shown with axes x,y,v and w indicated. If the angle measurements on the figure are c=20o , d=9o , f=15o and g=7o, determine the x-component of FA (lb).
Consider the truss shown in (Figure 1). Suppose that F1 = 60 kN and F2 = 20 kN . Part A Determine the force in member ED of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Part B Determine the force in member EH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Part C Determine the force in member GH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.
Consider the truss shown in (Figure 1). Suppose that F= 7 kN . Part A Determine the force in member HI of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Part B Determine the force in member FI of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Part C Determine the force in member EF of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.72 mm the values of elastic modulus for steel is 223 MPa. Take H1 = 7 cm, H2 = 10 cm, top bar (R) is 2 x 2 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = ii) Stress-induced in the top bar = iii) Stress-induced in the bottom bar =
Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given: A1 = 0.94 in2, A2 = 0.38 in2, P1 = 81 kips, P2 = 49 kips, P3 = 31 kips and E = 29x106 psi Your final answer should have three decimal places
Hello, Could you please help determine elastic center C Where the square has a modulus of elasticity = E_w and the two riangle has modulus of elasticity E_f = 3* E_w
Determine the maximum tensile stress and maximum compressive stress due to the load P acting on the simple beam AB (see figure). Data are as follows: P= 5.4 kN L=3.0 m d=1.2 m b=75 mm t_=25 mm h=100 mm h1=75 mm c1=62.5 mm c2=37.5 mm, and l= 3.3203x10⁶ mm⁴
The two vertical rods attached to the light rigid bar in the figure are identical except for length. Before the load W was attached, the bar was horizontal and the rods were stress-free. Determine the load in each rod if W = 6600 lb. (Determine load for rod A & B in lbs)
Determine the total deformation in inches if the flexural rigidity is equivalent to 5,000 kips. 0.0589 0.0658 0.0568 0.0696
The two vertical rods attached to the light rigid bar in the figure are identical except for length. Before the load A (in lbs) was attached, the bar was horizontal, and the rods were stress-free. Determine the load in each rod.
Joists support a floor and transfer their load to beams at each end of each joist. Joists are 2 ft on center and 30 ft long. If w, the load on the floor, is uniformly distributed and is 30 lb/ft2, what is the load on one joist? If the maximum flexural stress S in a joist is given by S = M/Z, where M is the maximum bending moment (pound-foot) and Z is the section modulus (cubic inches), what is the stress in a joist that has a section modulus of 50 in.3 and is 30 ft long? Assume that the maximum bending moment for a simply loaded joist is given by M = wL2/8, If the joists are made of pine, which has an allowable bending stress of 9,300 lb/in.2, will it carry the load?
A pin-jointed plane truss shown in Figure Q1 is supported by a roller at point A and pinned at point G. Vertical point loads of 5 kN are acting downward at points B, C and D. As a structural engineer, you are responsible to check the stability and analyse all of the members in the truss.c) Determine the internal force of each member by using an appropriate method?