is three times larger than in steel shaft. Q1) For the section shown aside, if the bending stress at point B is 245 MPa, what is the maximum bending stress on the cross-section? 20 mm 150 mm A) 225 MPa B) 170 MPa C) Zero N- 20 mm D) 255 MPa 150 mm E) Moment is required in calculation 20 mm -250 mm-

is three times larger than in steel shaft. Q1) For the section shown aside, if the bending stress at point B is 245 MPa, what is the maximum bending stress on the cross-section? 20 mm 150 mm A) 225 MPa B) 170 MPa C) Zero N- 20 mm D) 255 MPa 150 mm E) Moment is required in calculation 20 mm -250 mm-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam has the following properties: fc'=28MPa fy=270MPa b=300mm d=450mm As=4 of 36mm diameter bars Compute For: 1.) The magnitude of the ultimate moment capacity is Blank 1 kN.m 2.) If the fc' is reduced by 50%, the depth of the concrete stress block is Blank 1 mm.
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11400 psi, and the vertical deflection of joint D is not to exceed 0.425 in. when a load of P = 3400 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 94 in., b = 30 in., and c = 38 in.
A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer at the tension side. The beam has a stirrup with a diameter of 10 mm. Use fc=28 Mpa and fy=420 MPa GIVEN: b= 390.5 mm d= 610.5mm L= 6.45 m Wd = 13.5 kN/m WL = 35.5 kN/m Calculate the nominal moment capacity of the beam Calculate that strain of the tension bars. Calculate the strength reduction factor of the beam
Find the value of maximum load P sothat the stresses in the frame illustrated willnot exceed 120MN/m2 in tension or 90MN/m2in compression.The bars of the pin-connected frame shownhave a section of 35mmx65mm each.
•Timber beamSafe working stress = 25 MPaCross-section dimensions:height = 119 mm,width = 66 mmProving ring number 293. Steel beam Safe working stress = 200 MPa Cross-section dimensions:external height = 149 mm,external width = 50 mm,wall thickness = 3.0 mm,Proving ring number 1522.1)Calculate safe max bending moment in the central part of the beam using Mmax = (I)(max stress)/(D/2)2) calculate Safe applied force in the proving ring or tie rod, assuming a symmetrical setup as in the photowith a ‘lever arm’ of 600 mm
The torque off 100 kip-ft produces a maximum shear stress of 8000 psi in the 16-ft long hollow stee shaft. Note that the inner diameter of the shaft is two-thirds of its outer diameter D. (a) Determine the outer diameter D. (b) Find the angle of twist of the shaft. Use G = 12 x 106 psi for steel. Write legibly please
Question (1): A rectangular beam has a width b = 400 mm, and effective depth d = 850 mm and a total height h = 900 mm. The beam is subjected to an ultimate moment Mu = 1500 kN.m and an ultimate shear force Vu = 700 kN. 1- ) Design the beam for flexure to calculate the required area of steel. 2-) Using stirrups Φ 10 mm ( No.10) diameter, calculate the required spacing (s) between the stirrups at the ultimate shear force section. For all questions, Use f’c= 28 MPa and Fy= 420 MPa
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
Refer to the figure shown below, the hinged support at A is in double-shear connection while the support at B in single shear shear connection. Forces P is applied at C and F is an axial force produced from a member BD connected at B. Given data: x = 1.2 m, y = 1.5 m and z = 1.8 m. ∅ = 20 degrees Which of the following most nearly gives the maximum value of P in kiloNewtons if the shearing stress of 12-mm-dia. pin at A is 120 MPa. The horizontal distance between point A and B is 0.75x.
Q) Determine the elastic and plastic moment of resistance of the RC beam. The beam is a trapezoid in shape. B1 at top = 300mm, B2 at bottom = 500mm, total height = 600mm, height from top to the bottom of the steel reinforcement = 570mm, As = 1473mm^2, Fy=350MPa, Fcu=30MPa Solve this early I upvote
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. Determine the maximum flexural stress on the beam in MPa. Determine the maximum shearing stress on the beam in MPa.