using method of sections. Determine the forces in members BC, BG, and FG.

Q: Use centered difference approximations to estimate the first and second derivatives of y = e* at x =…

A:

Q: ater backs up behind a concrete dam as shown in the figure. Leakage under the foundation gives a…

A: Given: L=120ft, Hdam=80ft, specific weight of the concrete = 150 lb/ft3

Q: On what cases are these following surveying curves used: simple curves, compound curves, reverse…

A: On what cases are these following surveying curves used: simple curves, compound curves, reverse…

Q: Q3/A levelling survey was done for a project at station A to draw the cross section. The design…

A:

Q: 15 10 5 15 5< 10 The ratio of major farincipal strees to minor principal stren will be

A:

Q: 2. Determine the design strength P of an A992 W18x50 connected by bolts on plates on both flanges as…

A: Answer  From AISC Manual Table 1-1 W shape properties W 18 x 50 ( A = 14.7 in2 , bf = 7.50 in, tw =…

Q: Determine the correct length of a line reduced to the mean sea level when the recorded length with a…

A: Answer  Correct length of a line is given by Correct length = Measured length - Total corrections…

Q: B.M=0.740m 0+00 A 1.50m 0+05 B 1.54m 0+10 с 1.865m 0+05 1.715m 0+02.5 1.80m 0+15 D 2.565m 0+02.5-…

A:

Q: 30 K 15 20 15 130 20 Ratio of major principal stress to minor principal stress up to two decimal…

A:

Q: Required information. Consider the given state of stress. Take X= 16 MPa and Y= 48 MPa. Y + X 60 MPa…

A:

Q: 1. The following data shows the results of the liquid limit and plastic limit test using Casagrande…

A:

Q: ears and has a salvage value of PZ of the 5 years using the Straight Li Year 0 1 2 3 Book Value P…

A:

Q: 3. Solve for the support reactions at the fixed supports D, E, and F. Use cantilever method.

A: Answer We need to locate centroidal axis first for the given frame Consider span member have same…

Q: Number

A:

Q: Draw the determine the V 10KN and value 2m diagram of the continous of eiy. 25kN/m + 2 15 kN/m TH डm…

A: Given: Required: Shear and moment diagram  Value of EIy

Q: 11. Draw the influence lines for the forces in the members identified by an "X" mark of the truss…

A: ### Drawing of ILD for the forces in the members identified by X as GH , CH, CD, HD ###of given…

Q: If a 2-story building is 20ft high with 10ft floor-to-floor heights, and 5kip story shear forces at…

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: Determine the common tangent of a reversed curve given the following properties: D1 = 4.98° 11 =…

A:

Q: P = 49 kips Determine the normal and shearing stress at point a, b, and c

A: Normal stress is defined as the force that acts in the perpendicular direction. Shear stress is…

Q: Q- In an excavation of 3,000 cubic meter of common earth for a canal project, 6 men can be…

A:

Q: Describe in language appropriate to a client for a multistory office building what the structural…

A:

Q: Soil Parameters w (%) kN Y Yd= Y 1+w Sample 1 6.2 16.9 15.9 Sample 2 Sample 3 8.1 9.8 18.7 19.5 17.3…

A:

Q: For the structure shown in Figure P-916 is hinged to fixed supports at A and E. Compute the maximum…

A:

Q: 80 KN -30 kN/m A 6m B

A: Concept Here we will calculate the reactions at each support using the equation of equilibrium.…

Q: Given the following, solve for the middle ordinate: • D = 5° 1 = 40.038° NOTE: Solution not required

A:

Q: what is the redox reaction for hardness in freshwate

A: The hardness of water is defined as the concentration of the dissolved salts in water that is salts…

Q: 6 kN/m 30 kN T ttt 3m (b) 20 KN |20|1=1

A:

Q: In a laminar Poiseuille flow between two parallel plates, the ratio of average velocity to the…

A: Poiseuille flow is defined as a flow produced by pressure over a pipe. The equation for laminar…

Q: What are the chances of having a 6.5 earthquake within 50 km of Reno in the next 50 years

A: This question is related to the Earthquake engineering from Civil Engineering. In this question ask…

Q: Define fundamental volume-related geotechnical engineering properties

A:

Q: Which of the following does NOT belong to a risk assessment? O Risk estimation Exposure assessment O…

A: Brief concept introduction- Risk assessment- A risk assessment is a process used to determine which…

Q: Problem 1.29. A steel rod of 3 cm diameter and 5 m long is connected to two grips and the rod is…

A: Given : Diameter of steel rod = 3 cm  Length = 5 m E = 2 X 105 MN/m2 To Find : Determine the stress…

Q: What are the disadvantages of sand plumbing?

A: Sand Plumbing- Sand plumbing describes a pipe that either contains sand or acts as a route for it.…

Q: In the Stoke's experiment of falling sphere, it is found that a sphere of 5 mm diameter falls in a…

A:

Q: Express the internal shear and moment in the beam as a function of x and then draw the shear and…

A:

Q: 1 Gate AB is 2.0 m wide perpendicular to the paper and open to let fresh water out when the sea…

A:

Q: A 3 m long simply supported beam of uniformcross section is subjected to a uniformlydistributed load…

A: A simply supported beam of span 3 m supported at P and Q with hinge and roller respectively. A UDL…

Q: ft., then F2 = 12 x 2 kips = 24 kips (an unrealistic load, but just for the sake of argument, go…

A:

Q: 3 A rectangular gate AB hinged at A has a width 2.0 m perpendicular to the paper, has a negligible…

A:

Q: Draw

A:

Q: Problem 10.8 - A beam is built up from two standard rolled-steel mỹímýmỹmm mỹmmmmjumm mmg…

A:

Q: Q- In an excavation of 3,000 cubic meter of common earth for a canal project, 6 men can be…

A: Given data- Volume of excavation V=3000 m3, Number of men employed=6, One man output=100 m3/day, To…

Q: A section of highway has a superelevation of 0.05 and a curve with a radius of only 300 ft. What…

A: Given: R=300ft, e=0.05

Q: Q5/ The information below was taken from Longitudinal survey of road project. Draw the longitudinal…

A: To find draw the longitudinal section of the road way and to find the depth of fill/Cut at each…

Q: did it is multiplied by 1.5

A:

Q: 1. Three forces are applied to the bar shown. Calculate principal stresses and maximum shearing…

A:

Q: 10-30. Determine the moment of inertia for the beam's cross-sectional area about the x axis. 10-31.…

A:

Q: alvage value of P 125,000.00. Determine its depr traight Line Method. Year 0 1 2 3 4 5 6 Book Value…

A:

Q: Q- When the bearing of a line was measured with a compass, it came to be N42°15′W. If the magnetic…

A: Given- Bearing given =N42o15'W, Magnetic declination = 4o45' E, It is needed to find the true…

Q: The common tangent AB of a compound curve makes an angle with the tangents of the compound curve of…

A: Given, ∆1=28.5°∆2=35°Stationing of A=10+632.42D1=5.5°D2=6°to determine,a)Radius of the simple curve…

Load on Structures

Civil engineers primarily deal with beams in their day-to-day applications. A beam is a structural member that resists shear loadings. There are various types of beams such as cantilever beam, simply supported beam, and over the hanging beam. All these beams have a different end and loading conditions.