i need the answer quickly Using the following primary settling tank data,determine the daily sludge production.Operating DataFlow = 0.150 m3 · s-1Influent suspended solids = 280.0 mg · L- = 280.0 g%3D%3Dm-3Removal efficiency = 59.0%Sludge concentration = 5.00%Volatile solids = 60.0%Specific gravity of volatile solids = 0.990Fixed solids = 40.0%%3DSpecific gravity of fixed solids = 2.65

As math type is not available, Providing Hand written solution to you,

Using the following primary settling tank data, determine the daily sludge production. Operating Data Flow = 0.150 m3 ·s-1 Influent suspended solids = 280.0 mg · L-1 = 280.0 g -3 m Removal efficiency = 59.0% Sludge concentration = 5.00% Volatile solids = 60.0% Specific gravity of volatile solids = 0.990 Fixed solids = 40.0% Specific gravity of fixed solids = 2.65

Using the following primary settling tank data, determine the daily sludge production. Operating Data Flow = 0.150 m3 ·s-1 Influent suspended solids = 280.0 mg · L-1 = 280.0 g -3 m Removal efficiency = 59.0% Sludge concentration = 5.00% Volatile solids = 60.0% Specific gravity of volatile solids = 0.990 Fixed solids = 40.0% Specific gravity of fixed solids = 2.65

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.8P

See similar textbooks

Similar questions

The hydraulic conductivity of a homogeneous sandy/gravelly aquifer is 3 x 10-2 cm/sec. The hydraulic gradient (groundwater surface slope) of the phreatic (water table) aquifer is 0.009 and the aquifer's effective porosity is 0.28. Calculate the following : The average velocity of dissolved salt (travels at same speed as groundwater). Enter your answer in meters/year, to the nearest whole meter/year.
Calculate in units of hours the hydraulic retention time at peak flow in a settling tank based on the following information The settling tank is rectangular with 5 m depth. The surface loading rate is 20 cubic meters per square meter and per day at dry weather flow (DWF). Peak flow is 2 times the DWF.
The following data relate to a pump-out test: Diameter of well = 24 cm; Thickness of confined aquifer = 27 m; Radius of circle of influence = 333 m; Draw down during the test = 4.5 m; Discharge = 0.9 m^3/s.What is the permeability of the aquifer in mm/s? Choices: a. 2.15 x 10^-2 b. 4.5 x 10^-1 c. 93 X 10^-1 d. 1.6 X 10^-1
The hydraulic conductivity (K) of a homogeneous sandy clay mix aquifer is 2x10-3 cm/sec. The hydraulic gradient (groundwater surface slope) of the phreatic (water table) aquifer is 0.01 and the aquifer's effective porosity is 0.35. Calculate the average (advective) velocity of a conservative contaminant discharged to this groundwater unit. Enter your answer rounded to the nearest tenth in meters/year. Example: 5.2 , 65.7, 224.3 would all be proper forms of your answer.
a) An activated sludge plant with recycle is evaluating its secondary clarification system. Settling column tests are conducted and analyzed for settling velocities at different initial solids concentrations. The data are provided below. The plant flow rate is 10,000 m3/d, with a recirculation ratio of 0.5. The MLSS in the reactor is 4000 mg/L. The desired underflow concentration is 17,000 mg/L. Solids concentration mg/L Settling velocity m/h 1500 6.5 3000 5.1 4500 4 6000 2.95 7500 2 9000 1.4 12,000 0.5 15,000 0.27 17,000 0.2 b) Design secondary clarifiers for the activated sludge plant of problem a), with a recycle ratio of 0.6. Calculate the required surface area if two clarifiers are used. Also calculate underflow rate, underflow velocity, and overflow rates. Clearly state your assumptions.
Sedimentation tank is used for a flow rate of 0.2 m3/s and has dimensions 32m x8m x4m. The density of the particles = 2.5 g/cm3, density of water = 1 g/cm3, and the dynamic viscosity of water = 0.01 g/(cm.s). Determine the removal efficiency if the diameter of the particles is 25 um.
For a falling-head permeability test, the following values are given: Length of specimen = 200 mm Area of soil specimen = 1000 mm^2 Area of standpipe = 40 mm^2 Head difference at time t = 0 = 500 mm Head difference at timt t = 3 minutes = 300 mm Determine the hydraulic conductivity of the soil in ×10−4cmsec Please answer this asap. For upvote. Thank you very much
If the settling velocity of a particle is 0.70 cm/s and the overflow rate of a horizontal flow clarifier is 0.8 cm/s, what percent of the particles are retained in the clarifier?
A rectangular sedimentation basin with a length twice the width and 3 m deep, receives a flow of 2400 m/day with a normal concentration of suspended solids of 120 mg/l Determine: 1. The surface over flow rate (SOR) when the detention time is 6 hours. 2 The water entering velocity to the basin (cm/min) 3. The efficiency of the basin when the total mass of sludge produced per day is 216 kg.
An unconfined aquifer is 100 feet thick was evaluated using a field pumping test. The depth to groundwater is 10 feet. At a distance of 1000 feet, the drawdown was 40 feet, and at a distance of 5000 feet it was 20 feet. Find the permeability of the aquifer assuming that a steady-state of 960 gal/minute during the test in ft/sec.
2. Determine the efficiency of removing particles of size 50 μm and density 1,100 kg/m², settling in a horizontal sedimentation tank of depth 2m, length 10 m and length to width ratio of 3:1. The flow into the sedimentation tank is 2000 m³/d. The dynamic viscosity (u) can be taken as 1.002 x 10* Pa.S.
A rectangular sedimentation tank has dimensional proportions of 10:1:3 (L:W:H). If sedimentation is done in batch, the tank can cater 1080 m^3 in one hour, while the detention time for a continuous settling is 15 minutes on the same tank. a) During batch sedimentation, how many batches is done in an hour? b) Solve the dimensions of the tank. c) If the critical settling velocity is 0.003m/s, how many percent of the solids will be settled down? d) If the influent has a solids concentration of 230 mg/L and the effluent is 90% of the influent, compute the solids concentrations both at the underflow and the overflow. e) Determine the filter area if the filter loading rate is 2.3 gal/d.ft. ANSWER D AND E I PROVIDED SOME INFORMATION THANK YOU!