Using various types of transformers, give 10 impacts to the end-users per type of transformer in terms of physical features, advantages and applications. Type of Transformers 1. Step-Up Transformer 2. Step-Down Transformer 3. Two Winding Transformer

Using various types of transformers, give 10 impacts to the end-users per type of transformer in terms of physical features, advantages and applications. Type of Transformers 1. Step-Up Transformer 2. Step-Down Transformer 3. Two Winding Transformer

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.14P: A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down...

See similar textbooks

Related questions

Q: R 6.2 E=940° ZL a) Find load impedance of maximum power transfer ZH=ZL (VTH) %3D b) Find maximum…

A: Let Zs = (R+jX). Then for delivery of maximum power from source to load, the value of load impedance…

Q: G2 R H1

A: We need to find out transfer function for given system

Q: Draw an equivalent circuit of a transformer with all parameters referred to secondary. You can…

A: To draw the equivalent circuit diagram of a transformer with all parameters referred to secondary…

Q: Zeg 1-j2 1+j3 2 1+j2 2 j5 2 Find Zeq for this circuit. Show all your work.

A: All the impedance are parallel and share the common node with P and R Given Z1 = 1-j Ω , Z2 = 1+j2…

Q: /Determine the DC bias voltage VCE and the current IC for the configuration of figure (3) using…

Q: From the data collected in Tables 1 and , plot the current versus voltage characteristic of the…

A: The voltage-current characteristics plot is a basic graphical representation to study any circuit…

Q: 5. For the following circuit, determine v.(t) for t>0. t D0 9 k2 3 kΩ No 20 µF = % 36 V

A: To find the voltage across capacitor vo(t) for t>0

Q: Instructions: • Write the GIVEN with their respective symbols and units. Do not skip the SOLUTIONS,…

A: We need to prove the given Laplace transform property .

Q: Forward transconductance is the change in drain voltage for a given change in gate voltage. True…

A: 1)Forward transconductance is the change in drain voltage for a given change in gate voltage.…

Q: Consider the circuit of Fig. The two sources are is1 = 2 cos t mA and is2= 1.5 sin t mA. If M1= 2H,…

Q: The generator of a motor-generator set is delivering its full-load output of 10 kilowatts. The…

A: The solution is given below

Q: 25. a. Calculate the resistance associated with the JFET of Fig. 6.22 for Ves = 0 V from Ip - 0 mA…

A: The resistance value can be obtained from the graph using the ratio of voltage to the current.

Q: A thyristor half-wave controlled converter has a supply voltage of 240V at 50Hz and a load…

A: Given values are : The given root mean square value of supply voltage is Vsrms=240 The value…

Q: 5.3 Find i (in milliamperes) in the circuit in Fig. P5.3. PSPICE Figure P5.3 MULTISIM 8 kN 4 kN 20 V…

A: We need to find out current for the given circuit

Q: Use Kirchoffs Law

Q: Explain why the proportional relationship between the magnetic field strength of an electromagnet…

A: The reason is very simple which is based on Faraday's law of induction

Q: Q3//For the network of following Fig., determine: a. re. b. Zj. Z, (r. = 0N). d. A, (r, = ∞N). с.…

A: As per our company guidelines we are supposed to answer only first 3 subpart kindly repost the other…

Q: Q1: Considering the modulation constellation diagram in figure below, (0,1) (0,0) x,(k) -2 12 Ston…

A: a) The modulation is Quadrature Phase Shift Keying (QPSK)

Q: Three resistors of 50 N, 100 N and an unknown resistance R are connected in parallel and the…

Q: Does the circelit Amplify? why or Why not Find and Deaw Vout Vin 50sinwt (mU) RE R= SKL

A: According to the question, for the given circuit as shown below We need to find whether the circuit…

Q: : J. A current sheet, K = 2.4a. A/m, is present at the surface p = 1.2 in free space. (a) Find H for…

A: In Ampere law says that line integral of magnetic field of a surrounding close loop equal to number…

Q: P1. 27. Given vectors A, B, and C, evaluate 3|A|C•2B if Ax = 7 Ay = 3 Az = -3 Bx = 1 By = 2 Bz = 3…

Q: Solve for the branch currents using any method. 50 10V 12Ω www 10Ω 10Ω 12V 150 ww

A: In this question, We need to determine the branch current in the circuit using the any method. We…

Q: Determine the output voltage, Vo in mV. R1=13250 ohms, R2=6430 ohms and peak input voltage of…

A: solving opamp circuit by vartual short property inverting terminal voltage = positive terminal…

Q: 1) If an up counter has 10 flip-flops and its initial count is 0, what count will it hold after 2070…

A: In this question, We need to choose the correct options What is count will be hold after 2070…

Q: For an RC Circuit: a. Using information from the graph, find t b. If R= 6982 0, calculate C (use the…

A: The given voltage vs time graph of the RC circuit is shown below. We need to determine the time…

Q: Consider the circuit shown below, the transistor parameters are: B = 100 and VA = 100 V Vcc = 9 V R1…

A: Solve first three sub-parts in a multiple sub-part question, unless the student has asked for…

Q: 1 Normal Styles Paragraph Question 3 a) What loss does laminating the iron core of a transformer…

A: In this question we will write about what loss in transformer reduces by lamination.....

Q: 2. Calculate inductive reactance (Xc) and total impedance (Z;)

Q: Question 6 (a) A parallel network consists of two branches A and B. Branch A has a resistance of 10…

A: V=230Vf=50HzBranch-A:Resistor '10Ω' in series with inductor '0.1H'.Branch-B:Resistor '20Ω' in…

Q: The registers are involves in Indirect Cycle are: MAR, MBR O MAR, MBR, IR MAR, MBR, Control unit.…

A: After the fetch cycle is completed, the source operands are fetched and the indirect cycle occurs…

Q: QI: The voltage applied across a capacitor having a capacitance of 10 micro Farad is shown. Write…

Q: Consider a system with the following closed loop characteristics polynomial: s+ 6s + 11s?+(K+6)s +Ka…

A: The solution is given below

Q: Given are the following differential equations. Find inverse Laplace Transform of the given DE.…

A: In this question we will find solution of differential equation using Laplace transform ..

Q: 42. Calculate the average power delivered to the 400 m2 and 21 resistors, respectively, in the…

Q: R1 R2 Vo Vin etermine the output voltage, Vo in mV. 1=13931ohm, R2=5112ohm and peak input voltage of…

A: In this question we will find output voltage of opamp....

Q: alculate the value of Ix and the base current going to the input and output stage for the circuit…

A: In all the BJTs the emitter and base of each BJT gets short circuited and hence each BJT will be in…

Q: A 240V, 50Hz supply feeds a highly inductive load of 500Ω resistance through a thyristor bridge that…

Q: 5. A single-core 66 kV cable has a conductor diameter of 2 cm and a sheath of inside diameter 5-3…

Q: Section 5.4 5.12 The op amp in Fig. P5.12 is ideal. a) What circuit configuration is shown in this…

A: We need to find analyse the given circuit

Q: Using left side of the divergence theorem, find the total charge enclosed in the rectangular…

Q: II Review The circuit shown in (Figure 1) contains a voltage- controlled current source. Suppose i =…

A: The solution is given below

Q: What is the wavelength corresponding to a frequency of 300 MHz?

Q: A current i = 5 + 14.14 sin (314 t + 45°) is passed through a center-zero PMMC, hot-wire and moving…

A: In this question, We need to determine the reading of the meter if a current is passing through…

Q: 1 1 x(z) = ;ROC: |Z| > 0.4 (1-0.4z-1) (1–0.2z-1) x(n) = %3D

Q: Practice Problems (2) Calculate: core/cladding interface The angle of refraction at the air/core…

A: It is given that: nair=1ncore=1.46ncladding=1.43θincident=12°

Q: Requized: Reg

A: The circuit is given as Now the equivalent resistance seen by the source will be…

Q: Semiconductors having band gap near 1.5 eV are preferred for solar cells because, select the best…

A: High band gap devices such as 1.5 eV absorb more number of photons from sun radiation as compared to…

Q: A non-inverting amplifier is implemented using an LM741 operational amplifier. In the shown circuit,…

A: Note: As per the policy we can solve only 3 sub-parts of a question, please re-upload the remaining…

Q: What makes this a common source amplifier?

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Using various types of transformers, give 10 impacts to the end-users per
type of transformer in terms of physical features, advantages and
applications.

Type of Transformers
1. Step-Up Transformer
2. Step-Down Transformer
3. Two Winding Transformer
4. Autotransformer
5. Power Transformer (Three-Phase Transformer)
6. Distribution Transformer
7. Potential Transformer
8. Current Transformer
9. Dry-Type Transformer
10. Oil-Immersed Type Transformer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the oneline diagram shown in Figure 3.40. The three-phase transformer bank is made up of three identical single-phase transformers, each specified by X1=0.24 (on the low-voltage side), negligible resistance and magnetizing current, and turns ratio =N2/N1=10. The transformer bank is delivering 100 MW at 0.8 p.f. lagging to a substation bus whose voltage is 230 kV. (a) Determine the primary current magnitude, primary voltage (line-to-line) magnitude, and the three-phase complex power supplied by the generator. Choose the line-to-neutral voltage at the bus, Va as the reference Account for the phase shift, and assume positive-sequence operation. (b) Find the phase shift between the primary and secondary voltages.
A single-phase l0-kVA,2300/230-volt,60-Hz two-winding distribution transformer is connected as an autotransformer to step up the voltage from 2300 to 2530 volts (a) Draw a schematic diagram of this arrangement, showing all voltages and currents when delivering full load at rated voltage. (b) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of this kVA rating is transformed by magnetic induction? (C) The following data are obtained from tests carried out on the transformer when it is connected as a two-winding transformer: Open-circuit test with the low-voltage terminals excited: Applied voltage =230V, input current =0.45A, input power =70W. Short-circuit test with the high-voltage terminals excited: Applied voltage =120, input current =4.5A, input power =240W. Based on the data, compute the efficiency of the autotransformer corresponding to full load, rated voltage, and 0.8 power factor lagging. Comment on why the efficiency is higher as an autotransformer than as a two-winding transformer.
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
What should be the focus of transformer preventive maintenance efforts?
Consider a bank of this single-phase two-winding transformers whose high-voltage terminals are connected to a three-phase, 13.8-kV feeder. The low-voltage terminals are connected to a three-phase substation load rated 2.0 MVA and 2.5 kV. Determine the required voltage, current, and MVA ratings of both windings of each transformer, when the high-voltage/low- voltage windings are connected (a) Y-, (b) -Y, (c) Y-Y, and (d) -.
Three single-phase two-winding transformers, each rated 25MVA,54.2/5.42kV, are connected to form a three-phase Y- bank with a balanced Y-connected resistive load of 0.6 per phase on the low-voltage side. By choosing a base of 75 MVA (three phase) and 94 kV (line-to-line) for the high-voltage side of the transformer bank, specify the base quantities for the low-voltage side. Determine the per-unit resistance of the load on the base for the low-voltage side. Then determine the load resistance RL in ohms referred to the high-voltage side and the per-unit value of this load resistance on the chosen base.
A single-phase two-winding transformer rated 90MVA,80/120kV is to be connected as an autotransformer rated 80/200kV. Assume that the transformer is ideal. (a) Draw a schematic diagram of the ideal transformer connected as an autotransformer. showing the voltages, currents, and dot notation for polarity. (b) Determine the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of the kA rating is transferred by magnetic induction?
Using the transformer ratings as base quantities, work Problem 3.13 in per-unit.
A three-phase transformer is rated 1000MVA,220Y/22kV. The Y-equivalent short-circuit impedance, considered equal to the leakage reactance, measured on the low-voltage side is 0.1. Compute the per-unit reactance of the transformer. In a system in which the base on the high-voltage side of the transformer is 100MVA,230kV what value of the per-unit reactance should be used to represent this transformer?
The per-unit equivalent circuit of two transformers Ta and Tb connected in parallel, with the same nominal voltage ratio and the same reactan of 0.1 per unit on the same base, is shown in Figure 3.43. Transformer Tb has a voltage-magnitude step-up toward the load of 1.05 times that of Ta (that is, the tap on the secondary winding of Tb is set to 1.05). The load is represented by 0.8+j0.6 per unit at a voltage V2=1.0/0 per unit. Determine the complex power in per unit transmitted to the load through each transformer, comment on how the transformers share the real and reactive powers.
Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.
The ratings of a three-phase, three-winding transformer are Primary: Y connected, 66kV,15MVA Secondary: Y connected, 13.2kV,10MVA Tertiary: connected, 2.3kV,5MVA Neglecting resistances and exciting current, the leakage reactances are: XPS=0.09 per unit on a 15-MVA,66-kV base XPT=0.08 per unit on a 15-MVA,66-kV base XST=0.05 per unit on a 10-MVA,13.2-kV base Determine the per-unit reactances of the per-phase equivalent circuit using a base of 15 MVA and 66 kV for the primary.