Vater flow through a pipe system connected in series. he pipe data are given in the table below. Calculate he flowrate Q through the system. The total pressure rop from A to B is 150 kPa and the elevation drop is m. Pipe 1 2 3 V/₁ Q L (m) 100 150 80 D (mm) 80 60 40 f 0.0288 0.0260 0.0314 e/D 0.003 0.002 0.005 m/s m³/hr PIPE 3 Pwater = 1000 kg/m³ Vwater = 1.02 x 10-6 m²/s PIPE 2 PIPE.

Vater flow through a pipe system connected in series. he pipe data are given in the table below. Calculate he flowrate Q through the system. The total pressure rop from A to B is 150 kPa and the elevation drop is m. Pipe 1 2 3 V/₁ Q L (m) 100 150 80 D (mm) 80 60 40 f 0.0288 0.0260 0.0314 e/D 0.003 0.002 0.005 m/s m³/hr PIPE 3 Pwater = 1000 kg/m³ Vwater = 1.02 x 10-6 m²/s PIPE 2 PIPE.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ Neglecting losses, determine the discharge in Fig. below Oil sp gr 0.75 3 ft 4 in, diam Water
For the conduction of the water there is a height difference of 38 m. The results obtained from the hydraulic calculation for three different diameters are shown in the following table Diameter, in. Total head loss, mca 8 56.5 12 37.2 16 29.1 What will be the available driving load? TRANSLATED FROM Para la conducción del agua se cuenta con un desnivel de cotas de 38 m. Los resultados obtenidos del cálculo hidráulico para tres diámetros diferentes son mostrados en la siguiente tabla: Diámetro, plgs. Pérdida de carga total, mca 8 56.5 12 37.2 16 29.1 ¿Cuál será la carga de conducción disponible?
Water flows naturally from a tank A located at 20 m above the ground level , to a ground leveltank B . The connecting pipeline between tank A and tank B has an equialent loss coefficient of K .Determine the flow rate Q= ? ( USE g= 10 m 2/s) Note that K0,5 : square root of K. ANSWER: 20 / K0,5 m3/s
The head on a sharp-crested, rectangular weir was incorrectly observed to be 1.91 m. when it was actually 3.96 m. if the crest length is 4.57 meters, determine the percentage error (in percent) in the computed value of the flow rate Q. Use coefficient of discharge 0.945.
A long 0.3 m pipeline laid between two reservoirs carries a flowrate of 0.14 m3/s ofwater. A parallel pipe of the same friction factor is laid beside this one. Calculate the approximatediameter of the second pipe if it is to carry 0.28 m3/s
The system consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water into the reservoir? Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kvalve = 6.9 f = 0.0316 γ = 9810 N/m3 Choices: 3.44 Mpa 1.02 MPa 3.48 Mpa 1.00 MPa None of the choices
Is there a significant difference between the discharge coefficient derived from the experiment with that of coefficient of discharge from Francis formula? Discuss the possible reason for such discrepancy.
A hydroelectric power generating system is shown in the figure. Water flows from an upper reservoir to a lower one passing through a turbine at the rate of 286 liters per second. The total length of pipe connecting the two reservoirs is 186 m. The pipe diameter is 346 mm and the Hazen-Williams coefficient is 129. The water surface elevations of reservoirs 1 and 2 are 194 m and 69 m, respectively. Determine the power in kW required by the turbine if it is 63% efficient? Neglect minor losses. Round your answer to 3 decimal places.
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4.5 times the velocity head in the siphon. Determine the flow rate in the siphon in lit/sec Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: li/s Decimal Places required in the final answer: 3
Reservoir X (Elevation 369m) supplies water to reservoir Y (Elevation 195m) thru a 400 mm pipe. A turbine is installed in the same level with Reservoir Y. The total system flow is 220 gpm determine the the output power in Hp if the turbine is 65% efficient and the total headloss of the system is 4.5m.
b) Given the below conditions are given for a partially circular channel shown in Figure2.▪ Flow = uniform▪ Density, ρ = 998.0 kg/m3▪ Dynamic viscosity, μ = 1.002 x 10^-3 kg/m∙sCalculate the hydraulic radius, Reynolds number, and the type of flow.
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa