View Policies Current Attempt in Progress If the bottom of a pop bottle similar to that shown in the figure below, what would be the magnitude of the resultant force acting on the hemispherical bottom? The air pressure in the top of the bottle is 37 psi, and the pop has approximately the same specific gravity as that of water. Assume that the volume of pop remains at 2 liters. R= lb ~~~~Pair=37psi 4.3 in. diameter

View Policies Current Attempt in Progress If the bottom of a pop bottle similar to that shown in the figure below, what would be the magnitude of the resultant force acting on the hemispherical bottom? The air pressure in the top of the bottle is 37 psi, and the pop has approximately the same specific gravity as that of water. Assume that the volume of pop remains at 2 liters. R= lb ~~~~Pair=37psi 4.3 in. diameter

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter18: Mathematics In Engineering

Section: Chapter Questions

Problem 6P

See similar textbooks

Similar questions

An astronaut has a mass of 68 kg. What is the weight of the astronaut on Earth at sea level? What are the mass and the weight of the astronaut on the Moon, and on Mars? What is the ratio of the pressure exerted by the astronauts shoe on Earth to Mars?
11. Situation 4 - A block of wood 0.6 m x 0.6 m x “h” meters in dimension was thrown into the water, it floats with 0.18 m projecting above the water surface. The same block was thrown into a container of a liquid having a SG of 0.90 and it floats with 0.14 m. projecting above the liquid surface. Determine the specific gravity of the block. Round off to three decimal places.
A plunger (54 mm Ø and 0.5 m long) is moving through a horizontal cylinder (60 mm Ø) containing oil at a speed of 8 m/sec that has a viscosity of 7.1x10-6 m2/sec and specific gravity of 0.84. Calculate the force needed to maintain its velocity. Use 2 decimal places.
On a rough surface, Daniel pushes a carton with a mass of 30.0kg. The force F that is he applies is 608N with an angle of 55.0 degrees with the horizontal. In a time of 4s, the block's speed increases from 0.15m/s to 2.68m/s. a) Draw a free body diagram for your calculations b) Find the coefficient of kinetic friction between the flood and the block.
A rectangular tank 20 ft long by 6 ft deep by 7 ft wide contains 3 ft of water. If the linear acceleration horinzontally in the direction of the tank's length is 8.05 ft/sec2, a.) Compute the total force due to the water acting on each end of the tank and b.) show the difference between these forces equals the unbalanced force necessary to accelerate the liquid mass. i need an answer right away please sir , thanks.
A container holds two layers of different liquids, one fluid having a specific gravity of 1.1 is 30cm deep and the other fluid having a specific gravity of 1.6 is 40cm deep. A solid cubical metal having an edge dimension of 18cm and specific gravity of 6.5 is submerged such a manner that half of the cube is on the top layer and the other half in the bottom layer of fluids with the square base of the cube horizontal. Help me compute the weight WCUBE of the cubical metal in newtons, compute the buoyant force BFCUBE in newtons acting on the metal object, and compute the tension T in newtons in the wire holding the cube to maintain its position. please draw a figure
10. Situation 4 - A block of wood 0.6 m x 0.6 m x “h” meters in dimension was thrown into the water, it floats with 0.18 m projecting above the water surface. The same block was thrown into a container of a liquid having a SG of 0.90 and it floats with 0.14 m. projecting above the liquid surface. Determine the weight of the block in kN. Round off to three decimal places.
1. In calibrating a 10-mL pipet, a measured volume of water was transferred to a tared flask and weighed, yielding a mass of 9.9814 g. (a) Calculate, with and without correcting for buoyancy, the volume of water delivered by the pipet. Assume that the density of water is 0.99707 g/cm3 and that the density of the weights is 8.40 g/cm3. (b) What are the absolute and relative errors introduced by failing to account for the effect of buoyancy? Is this a significant source of determinate error for the calibration of a pipet? Explain. 2. Repeat the questions in problem 1 for the case when a mass of 0.2500 g is measured for a solid that has a density of 2.50 g/cm3. 3. Is the failure to correct for buoyancy a constant or proportional source of determinate error?
A storage tank has vertical sides and is filled with water to a depth of 1.5 m. On top of the water is found an additional layer of oil (SG = 0.8) with a thickness of 0.5 m. Assuming a unit thickness into the page, calculate the following: (a) Resultant force on the wall of the tank due to the fluids? (b) Moment caused by the fluids along the wall at the base of the tank?
Convert: 350 lb/ft^3 to kN/m^3, 200 lb·ft to N·m, and 8 ft/h to mm/s ?
The hot-air balloon contains air having a weight of 0.00193slugs/ft3, while the surrounding air having a weight of 0.00237slugs/ft3. Determine the maximum weight of the load the balloon can lift if the volume of air it contains is 120,000 ft3. The empty weight of the balloon is 200 lb.
An expansion tank for a domestic hot water system measures 73⁄4 inches indiameter and 201⁄4 inches long. What is the maximum volume the tank canhold?