Vinegar contains acetic acid (HC2H3O2), which is responsible for its acidity. In one analysis of a commercial vinegar brand, a 15.00 mL sample was titrated with 0.450 M NAOH(aq). It required 30.5 mL of sodium hydroxide to neutralize the acid in the vinegar sample. What is the molar concentration of acetic acid in the vinegar? O 0.305 M O 0.102 M O 0.221 M O 0.915 M O 0.458 M

Vinegar contains acetic acid (HC2H3O2), which is responsible for its acidity. In one analysis of a commercial vinegar brand, a 15.00 mL sample was titrated with 0.450 M NAOH(aq). It required 30.5 mL of sodium hydroxide to neutralize the acid in the vinegar sample. What is the molar concentration of acetic acid in the vinegar? O 0.305 M O 0.102 M O 0.221 M O 0.915 M O 0.458 M

Chemistry: Principles and Practice

3rd Edition

ISBN:9780534420123

Author:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Publisher:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Chapter14: Chemical Equilibrium

Section: Chapter Questions

Problem 14.97QE: According to the Resource Conservation and Recovery Act (RCRA), waste material is classified as...

See similar textbooks

Similar questions

A commercial vinegar was analyzed by titration to determine the percent acetic acid. Briefly, 10.00 mL of vinegar sample was diluted to 100. mL solution in volumetric flask. A 25.00 mL aliquot from the diluted vinegar required 25.55 mL of 0.1005 M NaOH to reach the phenolphthalein endpoint. Which is the correct equation between the analyte and titrant reaction? CH3COOH + NaOH → NaCH3COO + H2O 2CH3COOH + NaOH → NaCH3COO + H2O C20H14O4 + NaOH → NaC20H14O4 + H2O CH3COOH + 2NaOH → NaCH3COO + H2O
1.00 grams of table salt was dissolved in 100 mL water and excess AgNO3 reagent was added and yielded 2.3789 grams of precipitate. Calculate the percentage of NaCl in the table salt. Answer must be in 2 significant figures.
A hydrochloric acid solution is standardized by titrating 0.5008 g of primary standard tris(hydroxymethyl) aminomethane, C4H11NO3, with 99.9780% purity. If 39.68 mL isrequired for the titration, what is the molarity of the acid?
3. how would the following errors affect the concentration of Cl- obtained in question 2b? give your reasoning in each case. a. the student read the molarity of AgNo3 as 0.02104M instead of 0.02014M b. the student was past the endpoint of titration when he took the final buret reading.
4 A sample of solid Ca(OH)2 was stirred in water at a certain temperature until the solution contained as much dissolved Ca(OH)2 as it could hold. A 84.3-mL sample of this solution was withdrawn and titrated with 0.0771 M HBr. It required 86.7 mL of the acid solution for neutralization. (a) What was the molarity of the Ca(OH)2 solution? M (b) What is the solubility of Ca(OH)2 in water, at the experimental temperature, in grams of Ca(OH)2 per 100 mL of solution? g/100mL
Mg(OH)2 is a sparingly soluble salt with a solubility product, Ksp, of 5.61×10−11. It is used to control the pH and provide nutrients in the biological (microbial) treatment of municipal wastewater streams. What is the ratio of solubility of Mg(OH)2 dissolved in pure H2O to Mg(OH)2 dissolved in a 0.200 M NaOH solution? Express your answer numerically as the ratio of molar solubility in H2O to the molar solubility in NaOH.
Iron (II) fluoride needs to be precipitated from a 77.07 L tank. If the concentration of iron (II) cation in the tank is 0.0330 M, how many grams of potassium fluoride must be added to the tank so that precipitation may begin? The Ksp of iron (II) fluoride is 2.36 x 10-6. (3sf)
Potassium permanganate solutions may be standardized by titrating against primary standard sodium oxalate: 2MnO4- + 5C2O42- + 16H+ → 2Mn2+ + 10CO2 + 8H2O. What is the molarity of the KMnO4 solution if 43.80 mL of the KMnO4 is required to titrate 0.2168 grams of Na2C2O4?
A student measured 20 drops of vinegar and one drop of phenolphthalein solution into a well of her well plate. After she had added 35 drops of NaOH solution to the same well, the well was full, but she had still not reached the titration endpoint. She then took a clean pipet and transferred some of the titration mixture into a second well. She rinsed the pipet with a few drops of distilled water and transferred the rinse water into the titration mixture in the second well. Then she continued adding NaOH solution to both wells until she reached the endpoint in both wells. She then recorded the total number of drops of NaOH solution added to both wells and used it to calculate the data for her vinegar titration. Briefly comment on her procedure and the accuracy of her results.
In a titration of Vinegar, the average volume of 0.1 M NaOH used after three titrations is 4.26 mL. If the density of vinegar (acetic acid) is 1.006 g/ml and the molecular mass of CH3COOH is 60.05 g/mol. The mass percent (%m/v) of the vinegar is: 5x10-5 5x10-4 0.5 5x10-3
The hardness of water (hardness count) is usually expressed in parts per million (by mass) of CaCO3. What is the molar concentration of Ca2+ ions in a water sample with a hardness count of 175mg CaCO3il? How many milliliters of concentrated sulfuric acid, 94.0% (w/w), specific gravity of 1.831 are required to prepare 1 liter of a 0.100 M solution? The solubility-product constant for Ce(IO3)3 is 3.2x1010. What is the Ce3+ concentration in a solution prepared by mixing 50.0 ml of 0.0250 M Ce3.. with 50.00 ml of water?
You have been provided with a 32.5ml sample of hydrochloride acid (HCl) of unknown concentration. You perform a titration with 1.50M sodium hydroxide (NaOH), and find that 3.75 x 10^-2 L are required to reach the equivalence point (as determined using a coloured indicator) what is the concentration of the hydrochloride acid solution in mol L^-1? To the correct number of significant figures.