Data obtained from short circuit & open circuit tests of 60 kVA, 3200-220 V are:Open circuit: Voc= 220 VShort circuit: Vsc= 150.6 V Isc=14.4 Aa) Determine transformer equation parameters.b) Draw the transformer equivalent circuit to high voltage side.5.Ioc=10.04 A Poc=440 WPsc=1000 W

Answered: Image /qna-images/answer/f7d78d6e-718c-4f3d-9303-7f01a17c74ef.jpg

Answered: Voc= 220 V Ioc=10.04 A Poc=440 W…

Voc= 220 V Ioc=10.04 A Poc=440 W Psc=1000 W Vsc= 150.6 V Isc=14.4 A nine transformer equation parameters. he transformer equivalent circuit to high voltage side.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Related questions

Q: 240V single-phase transformer has full load copper loss of 3 10 KVA, ratts and a core loss of 200…

A: Given, S = 10 kVA , 600/240 VPCu = 300 WPi = 200 Wcosϕ = 0.6 Cu losses at half load,…

Q: 22. In a single phase transformer Eddy current losses can be found by open circuit test Select…

A: to analyze the given condition

Q: The operated distfibution transformer has constant iron * and copper losses? False True

A: the operated distribution transformer has constant iron and copper losses true or false

Q: Answer by true or false * True False while conducting short- circuit on transformer the low voltage…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Single phase transformer rated for 24 kVA Primary is 12 kV, secondary is 480 kV • If a 10 Ohm load…

Q: TRUE or FALSE: If a 13800 / 480-V, three-phase transformer is connected wye-delta, then the turns…

Q: Ql-phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz . The resistance /phase and leakage…

A: (i) The per-phase secondary voltage in the star-connected secondary winding can be calculated as,

Q: The nominal specifications seen on the nameplate of a single-phase transformer are 600 MVA, 95/500…

Q: A load impedance of 52 ohms is connected to the secondary winding of the transformer with 208 volts.…

A: Using ohms law I=V/R Given voltage is 208 volts And impedance of 52 ohms

Q: By increasing the number of turns of wire on the secondary side of a single-phase transformer will

Q: A single-phase transformer rated at 55 KVA has no load voltage of 241 volts, when the regulation is…

Q: A single phase transformer has 360 turns and 180 turns respectively in its secondary and primary…

A: Transformer problem can be solved easily.

Q: Calculate the turns ratio from the transformer primary/secondary voltage ratings Using the…

A: Given Data at secondary side Voltage Current Power Open circuit 120 V 0.290 A 8.778 W Short…

Q: The resistance and reactance of the primary winding of a 440/110 V single phase transformer are 4.4…

Q: OPPO Reno3 - ©Marie Phone Using the image and using the rated values of the single phase transformer…

Q: (a) A 60-kVA, 4800/2400-V single-phase transformer gave the following test results: Rated voltage is…

Q: C2 (1). Draw the Schematic diagram and explain the working of LVDT and write any two applications of…

A: C2 (i) LVDT - It stands for the Linear Variable Differential Transformer. It is a inductive…

Q: 3. When an alternator connected to a particular load the calculated voltage regulation is -10.6%.…

Q: B- the eddy current losses of 400V, 50 Hz transformer is 1600W and the total iron losses i 2500W.…

A: Transformer Transformer is a static electrical device which transfers power from one circuit to…

Q: Ql-phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz .The resistance /phase and leakage…

Q: 4- The step-down transformer ?

A: Electrical machines can be either generator, motors or transformers. They can be either Ac machines…

Q: A single phase transformer is rated 4,160-V primary and 250-V secondary. It has 1,500 turns in the…

A: In this solution the concepts related to the regulation of a transformer is discussed. Given that…

Q: A 75 kVA, 230/115 volts, single phase transformer was tested with following test results: short…

Q: Ql-phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz .The resistance /phase and leakage…

Q: Ql-phase step down transformer 1250 KVA , 11000/2200 V, 50 Hz .The resistance /phase and leakage…

A: (i) The per-phase secondary voltage in the star-connected secondary winding can be calculated as,

Q: 4. A 220-kVA transformer with .2% resistance and 4% reactance and another 120-kVA transformer with…

Q: Q-2-c) The equivalent circuit impedances of a BK-VA, 6350/220-V, 50-Hz transformer are to be…

Q: Which is better, one transformer is used to feed the load or two transformers? Why?

A: Multiple transformers can be connected to reduce the size which improves surface area to volume…

Q: The apparent power in primary and secondary side of the distribution transformer remains the same at…

Q: Q3 (a) Draw the equivalent circuit for a single phase transformer with all components referred to…

A: Note: As per our policy, I have attempted the first question

Q: Maximum efficiency of a single phase transformer occurs at 80 percent of full load. What is the…

A: Given that maximum efficiency of single phase transformer occurs at 80 percent of full load.…

Q: In a 1-phase transformer, if the no load secondary terminal voltage is 227 V and the full load…

A: Although formula for voltage regulation is given by %VR=Vno load-Vfull loadVno load×100% Given…

Q: A single phase transformer gave the following results: Open Circuit Test: 250V, 1A, 80W Short…

Q: A 220-kVA transformer with .2% resistance and 4% reactance and another 120-kVA transformer with 3%…

Q: Q2. A 25-kVA, 2300:230-volt transformer is subjected to open- and short-circuit tests. The…

A: Transformer: Transformer is a static electrical device which transfers power from one circuit to…

Q: Figure shows primary line voltages (a) Identify the transformer connection. (b) Calculate…

A: In this question, We need to (a)Identify the transformer connection. (b)Calculate currents I2 and…

Q: A 1000-VA, 230/115-V traformer has been tested to determine its equivalent circuit. The results are…

Q: Q10) For the transformer shown in Figure below, determine (i) The turns ratio of the transformer…

A: A transformer has two windings - the primary and the secondary. The ratio of the number of turns in…

Q: The following values were seen in the measurements made separately by the primary and secondary of…

A: A transformer , the primary and secondary of a 220/270 V phase transformer. R1 = 4 ohms, X1 = 4.6…

Q: 4. A 220-kVA transformer with .2% resistance and 4% reactance and another 120-kVA transformer with…

A: In this question we need to find a load share by two transformer

Q: The following test results of a single-phase step-down transformer which were measured at primary…

A: 7. It is given that: Open-circuit test: VOC=415 V; IOC=0.22 A; POC=7.64 W; Vo=240 VShort-circuit…

Q: 6-Writ the procedure of no load test of Single phase transformer and draw the connection diagram of…

Q: 1- Using the voltage and current ratings, determine the tums ratio of the single-phase transformer?…

Q: a single phase transformer, when no-load voltage is 230V and full load terminal voltage is 220, then…

A: In this question , we have to find that given voltage regulation is correct or not...

Q: If the windings were connected subtractive, what voltage would appear across the entire connection?

Q: Ql-phase step down transformer 1250 KVA,11000/2200 V, 50 Hz .The resistance /phase and leakage…

Q: Ql-phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz . The resistance /phase and leakage…

A: Given values are =

Q: An open delta three phase transformer system has one transformer center tapped to provide a neutral…

A: It is given that: voltage from line to center tap=277 V

Q: True or false The taps of a multiple-tapped transformer are always on the load sid

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Data obtained from short circuit & open circuit tests of 60 kVA, 3200-220 V are:
Open circuit: Voc= 220 V
Short circuit: Vsc= 150.6 V Isc=14.4 A
a) Determine transformer equation parameters.
b) Draw the transformer equivalent circuit to high voltage side.
5.
Ioc=10.04 A Poc=440 W
Psc=1000 W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An RLC series circuit connected to a 110 – volt and 50 – cycle AC source, contains the following series resistances and reactances: R1 = 10 ohm, R2 = 15, R3 = 5 ohms, XL1 = 20 ohms, XL2 = 25 ohms, XC = 40 ohms. Find the following: a.) EQUIVALENT REACTANCE b.) TOTAL IMPEDANCE c.) VOLTAGE DROP ACROSS THE CAPACITOR d.) TOTAL INDUCTANCE IN MILLIHENRY e.) TOTAL CURRENT f.) REACTIVE POWER g.) REAL POWER DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES
10 A three-phase transformer is given. The number of turns of the high voltage winding is N1=850 and the number of turns of the low voltage winding is N2=34. The high voltage winding is energized with V1= 10 kV rms line-to-line and V2= 400 V rms line-to-line has been taken from the low voltage winding. What is the connection of the low voltage winding if the high voltage winding is Y-connected? Εισαγάγετε την απάντησή σας
Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
Transformer 1) Enumerate the way/s by which the voltage of the large coil may be: a) increased (AC source) b) reduced to zero (AC source) c) increased (DC source) d) reduced to zero (DC source)
How to generate 480V three phase 400Hz ac from 230V three phase 60Hz ac source? (Please specify the power components you pick, such as transformers, dc-dc converter, dc-ac converter and/or ac-dc converter, how these components are connected and the key parameters of these components, such as the turns ratio of transformer and the duty cycle functions for the converters.)
With base MVA of 150 and base voltage of 33. If the reactance of the transformer is 0.23 pu. The parameter of the reactance of the transformer in the Neplan software is O 1.66 2.30 23 0.23 O Non of them
A 1000-VA, 230/115-V traformer has been tested to determine its equivalent circuit. The results are shown below: Open-Circuit Test results from the low voltage side: Voc = 115 V, lọc = 0.1 A, Poc = 4 W; Short-Circuit Test results from the high voltage side: Vsc - 20 V, Isc = 8 A, Psc - 50 W; Determine the transformer's voltage regulation at 90% loading conditions and 0.8 PF leading.
6. A single-phase, 225-kVA, 460/120-V transformer has 6% impedance and 96% efficiency. Find its series Rand X in percent and in ohms looking from the HV side source. 7. Determine the rms fanlt currents on both sides of a 100-IVA single nhase
7. The primary of a single-phase transformer takes 1 A at power factor of 0.4 when connected to a 240-V, 50-Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. What is now the value of the primary current ? transformer.) (Neglect the voltage drops in the