Void Ratio (e) Cost Php/m3 400.00 Borrow Pit A 0.82 В 1.1 250.00 C 0.9 450.00 0.78 600.00

Q: m using area moment meth KN-m². W2 W1

A:

Q: If a PL = 20 %, LL = 40 % and natural water content was 18 % for a soil; what would be the liquidity...

A: Given data : Liquid limit (LL)=40% Plastic limit (PL)=20% Water content (w)=18%   To find : Liquidit...

Q: The selection of pile foundations for any project requires that the designer and contractor consider...

A: Step 1: Driven wood pile: Material type/wood type Strength parameter Driving force and handling Envi...

Q: A 16-mm-diameter, 15-m long cable is subjected to a load of 25kN. Compute the strain of the cable if...

A: solution Given diameter of the cable d=16mm length of the cable L =15mts =15000mm Load P =25KN =2500...

Q: 270 kN 45 kN/m В 3 m 3 m 3 m El = constant E = 200 GPa I = 1665x10°mm

A:

Q: The maximum tension in the steel rod is 580 N and the maximum stress in che link is 30 N/mm2. IT esi...

A:

Q: Determine maximum principal stress

A: Given data : The normal stress in X direction σX=-60 MPa The normal stress in Y direction σY=-40 MPa...

Q: ness álso providing superior riding and skid resista 4. The creation of one or more alternative rout...

A: 5.  The distance of one track to other is nothing but the distances around each lane.  

Q: Calculate for support reactions if: P=51 -Plot shear diagram -Plot moment diagram

A:

Q: Determine degree of stauration if water content 0.14, Void ratio is 0.5 and specific gravity of soil...

A: Given data : The specific gravity of soil solid G=2.7 The value of void ratio e=2.7 The value of wat...

Q: SANITARY PLANNING LAYOUT " F. SYMBOLS AND LEGENDS

A:

Q: Four wheel loads rolls as a unit across a 18-m span. The loads are 40 kN, 30 kN, 30 kN, and 10 kN se...

A:

Q: Cantilever method |ookN- 3. SM 200KN J + इम 6 sm 8m H IL

A:

Q: Replace the loading system by an equivalent resultant force FR and couple moment MR, acting at point...

A:

Q: Write the shear and moment equations (not simplified and simplified) at each segment of the beam. Dr...

A:

Q: Before projects can proceed, a contract must be drawn up between the customer and contractor. Define...

A: A contract is a legally enforceable contractual arrangement based on issues and criteria written dow...

Q: If a PL = 20 %, LL = 40 % and natural water content was 18 % %3D for a soil; what would be the liqui...

A: Given data: PL=20%LL=40%w=18%

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to in...

A:

Q: Convert 1,200 mils to grads. Select one: O a. 80 grads O b. 86 grads O c. 75 grads O d. 72 grads

A: Given  1200 mils Converting mils to grads

Q: Determine and draw the baseflow using; a. Straight line method b. Fixed based method using N = 5 С. ...

A: Baseflow separation from hydrograph can be done using three methods. They are  1. Straight line Meth...

Q: A. Given Design years for 2 direction of road Number of lanes 2 lanes ADT - 3500 Calculate the ESAL ...

A:

Q: A vertical rectangular gate 2.3 m wide and 5.1 m high is submerged in oil (SG=0.83) with its bottom ...

A:

Q: 4 kN/m 2 kN/m A B. 2 m- 3 m

A: Shear Force: The algebraic sum of all the vertical forces acting at different points of the beam is ...

Q: Assuming elastic behavior, why does the maximum shear stress always correspond to the neutral axis l...

A: The neutral axis is the axis at which strain and consequently stress is zero when the beam is subjec...

Q: Find the forces (kN) on the members of the given truss. Determine also the magnitudes of the support...

A:

Q: Use the conversion factors given on the front and back end covers of this text to convert the given ...

A: (a) Since, 1 ft is equal to 12 in so, The area can be expressed as,

Q: 3. 5P (kN) P (kN/m) 2.7P (kNm) 50° 3m u. 2m 3m 3m

A:

Q: 200 m 220 m 240 m 260 m |20 m|

A: contours are the lines joining the points of equal elevation   since contour value is increasing ins...

Q: Determine the maximum safe tensile force that can be supported by a 12 mm by 150 mm plate if its all...

A:

Q: Calculate for support reactions if: P=55 -Plot shear diagram -Plot moment diagram

A: To find support reaction and to draw SFD and BMD

Q: SIT. 2 The length of curve of a simple curve having a degree of curve 4 deg. is equal to 210 m. 1. C...

A:

Q: A saturated silty clay encountered in a deep excavation is found to have a water content of 21.7%. U...

A:

Q: A single-angle tension member, an L3 1⁄2 × 3 1⁄2 × 3⁄8, is connected to a gusset plate with 7⁄8-inch...

A:

Q: SANITARY PLANNING LAYOUT " C.   WATERLINE LAYOUT

A:

Q: A high-strength steel band saw, 25 mm wide, runs over pulleys 800 mm in diameter. What minimum thick...

A:

Q: The following data are for a variable head permeability test: Area of soil specimen=1200mm² Length o...

A:

Q: design flow of 0.186 m3/s when flowing partially, d/D= 0.67, slope= 0.4%, n=0.013    4. Calculate

A:

Q: Om 10m 20m 17.07m 0ATUM Y=18.86KN/m K = 10*m/sec B %3D Impervious (a) The elevation head, total head...

A: Geotechnical engineering is a civil engineering speciality that studies the behaviour and structural...

Q: and c = 70 mm. gage length A. a mm b mm c mm

A:

Q: Determine the slope and deflection at point B of the beam shown by moment area method. [ EI= constan...

A:

Q: A 30 ft wide UV treatment tank has a serpentine weir to regulate flow depth. The forks of the weir a...

A: Given:- The width of the UV treatment tank = 30 ft The forks of the weir = 1.5 ft wide The length of...

Q: Design a highway with the following criteria (Determine the minimum radius, widening and check if it...

A:

Q: 3.) Solve the system of simultaneous equations using Gauss-Jordan method 20x1 - 9x2 + 15x3 = 354 — 9...

A:

Q: A flat steel bar, 25 mm wide by 2 mm thick and 1.5 m long, is bent by couples applied at the ends so...

A:

Q: 9. Determine the force in member GJ and GC of the truss and state if this member is e in tension or ...

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of understandin...

Q: Determine the design compressive strength (kips) of a A36 steel column, W 10 X 33 with a total lengt...

A:

Q: 40 35 60 -60 35 140 MPa

A: Hello dear The answer is found to be Major principal stress =-13.6 MPa For explanation please see th...

Q: Find a diameter of pipe required to carry a design flow of 0.186 m3/s when flowing partially, d/D= 0...

A: Given data Q = 0.186 m3/sec d/D = 0.67 Slope (S) = 0.4% = 0.004 n = 0.013  

Q: The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading ...

A:

Q: 5. A closed traverse has the following data. | 等 LINE 1-2 2-3 LATITUDE +76.30 +33.80 DE PARTURE +43....

A:

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.