Assuming elastic behavior, why does the maximum shear stress always correspond to the neutral axis level? An under-reinforced beam section is safer than an over-reinforced one. Is this statement correct? Explain your answer using a sketch. What are the two fundamental equations/conditions in beam flexure analysis? Explain their use using neat sketches.

Assuming elastic behavior, why does the maximum shear stress always correspond to the neutral axis level? An under-reinforced beam section is safer than an over-reinforced one. Is this statement correct? Explain your answer using a sketch. What are the two fundamental equations/conditions in beam flexure analysis? Explain their use using neat sketches.

Construction Materials, Methods and Techniques (MindTap Course List)

4th Edition

ISBN:9781305086272

Author:William P. Spence, Eva Kultermann

Publisher:William P. Spence, Eva Kultermann

Chapter3: Properties Of Materials

Section: Chapter Questions

Problem 4RQ: How does a tensile stress differ from a compressive stress?

See similar textbooks

Similar questions

A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: 24 KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 and E = 200 GPa, Determine the total resulting strain in the z- direction. Note: CN is the last 2 non zero digits of your cellphone number
40-mm sides glass polymer fibers composite cube shown in Figure.2. The Glass polymer fibers aligned in the xdirection. The cube is constrained against deformations in the ? and ? directions and is subjected to a tensile loadof 60 ?? in the x direction. Estimate the strain, change in length and stresses in ?, ?, and ? directions as well asdetermine the volumetric strain. Illustrate the effect of three-dimensional strain by constructing appropriatesketches (before and after deformation for both cube and fibers, assume the fibers have radius of ?). Repeat theanalysis for lower value of tensile load and higher value in the range of [20 -100 KN] and comment on the overallresults. What will happen if the force is compression.
(a) Assuming elastic behavior, why does the maximum shear stress always correspond to the neutral axis level? (b) An under-reinforced beam section is safer than an over-reinforced one. Is this a correct statement? justify your answer using a neat sketch. (c) What are the two fundamental equations/conditions in beam flexure analysis? Explain their use using neat sketches.
SITUATION 21 A rectangular steel block is 300 mm in the x direction, 200 mm in the y direction, and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in x direction, 320 kN compression in the y direction, and 180 kN tension in the z direction. For Steel, Poisson's Ratios = 0.30 and E=200 GPa. 4. Determine the total strain in x direction due to the triaxial loading 5. What single uniformly distributed load in the x direction that would produce the same deformation in the x direction as he orig nal loading.
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.
Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
The cross-sectional areas of a column are shown in the figure . Find the maximum allowable value of P (in N) for the column if the stress in the steel is 84.96 MPa , stress in the timber is 17.21 MPa , and stress in the concrete is 18.52 MPa. Round off the final answer to two decimal places.
Situation 4. A cast iron link is 50mm wide by 250mm high by 550 mm long. The allowable stressin tension is 50 MPa and 85 MPa in compression. Assume that load P (tensile axialload) is placed at 30 mm distance from the neutral axis. A. What is the value of tensile normal stress in MPa? B. What is the value of bending stress in MPa? C. What is the value of the combined stress?
Discuss Computation of Effective Stresses
Q2: A cold drawn steel rod of circular cross- section is subjected to a variable bending momen of 565 N.m to 1130 N-m as the axial load varies from 4500 N to 13 500 N. Determine the required diameter of the rod for a factor of safety 2. Neglect any stress concentration and column effect. Assume the following values: Ultimate strength = 550 MPa Yield strength = 470 MPa Size factor = 0.85 %3D Surface finish factor = 0.89 Correction factors = 1.0 for bending = 0.7 for axial load The endurance limit in reversed bending may be taken as one-half the ultimate strength.
A beam made of Al 2014-T6 aluminum alloy is loaded by an oblique bending moment of M = 5 kN.m as shown in the figure. a) Calculate the tensile and the compressive stress values. b) Define the location and the orientation of the Neutral Axis and draw it on the figure. Note: The cross-sectional dimensions are the same with the one in the 3rd question of the final exam. Therefore, you do not need to find the location of the centroid and the value of the moment of inertia about the z axis, I, You can directly use the values in the 3rd question. 5 kN.m 90 mm 30 10 mm 90 mm ! 10 mm Window Windows'u