voltage given by v(t) = 311 cos (311 pi t) V is applied to a 50-ohm resistance. (a.) Sketch v(t) to scale versus time. (b.) Determine the rms value of the voltage and the average power delivered to the resistance. (c.)Determine the power as a function of time and sketch to scale.

voltage given by v(t) = 311 cos (311 pi t) V is applied to a 50-ohm resistance. (a.) Sketch v(t) to scale versus time. (b.) Determine the rms value of the voltage and the average power delivered to the resistance. (c.)Determine the power as a function of time and sketch to scale.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.30MCQ: Under balanced operating conditions, consider the three-phase complex power delivered by the...

See similar textbooks

Related questions

Q: Determine the RMS magnitude of Current I.

Q: An audio power amplifier delivers a 30 volt RMS 1 kHz sine to a loudspeaker. If the loudspeaker…

A: Given data, RMS voltage Vr=20 V Impedance is given Z=7∠450

Q: i) An alternating voltage E=200 Sin 314t is applied to a device which offers an ohmic resistance of…

A: Given , E = 200 sin 314 t R = 20 r

Q: A supply voltage v given by v = (240 sin 314t + 40 sin 942t + 30 sin 1570t) volts is applied to a…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: A resistor of 4 ohmsisconnected in parallel with an impedancecoil whose resistance and inductive…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: A voltage is given by v(t)=50 sin(500πt+120°).. First, use a cosine function to express v(t). Then,…

Q: Consider a sinusoidal voltage expressed as: v (t) = 170 cos(2760t – 40°) V a) Find the angular…

Q: An industrial heater has a nameplate that reads: 200 V, 60 Hz, 12 kVA, o.788 pf lagging Determine…

A: Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

Q: The power of a certain CD player operating at 120 V rms is20.0 W. Assuming that the CD player…

A: Given: Voltage, Vrms=120V Average power, Pavg=20W

Q: wall socket source is modeled as an ideal 120 V rms voltage source in series with a 2-ohm output…

Q: Example: Find the rms value for the current waveform shown below: 2 1 1 3 4 t(sec)

A: First we will find out the current equation then we will find out RMS value by RMS formula.

Q: Example 1: Calculate the RMS and the available power at the thermal noise in 100 2 at 27 C° and 6M.…

A: Given data, Resustance is given R=100 Ω Temperature is given as, T=270 C=273+27=300 K Bandwidth B=6…

Q: Find the resultant of the two out of phase current If the component currents are 12 and 16 amp.,…

Q: Household electricity in a particular country is supplied in the form of alternating current that…

A: The solution is given below

Q: Determine the rms (or effective) value ofv(t) = VDC + vAC = 50 + 70.7 cos(377t) V

A: Consider the expression, Write the expression for the rms value,

Q: Determine the rms value of v(t)=5+10 cos(20πt).

Q: The two loads shown can be described as follows: Load 1 absorbs an average power of 60 kW and…

A: a) Calculating root mean square value of load voltage is Calculating apparent power absorbed to…

Q: 1. Determine the RMS values of voltage and current, and the total power absorbed by the circuit…

A: In this question, two signals are given in harmonic form. We need to determine the rms value of…

Q: A 50 kW load operates from a 60 Hz, 10 kV rms line with a power factor of 0.6 lagging. Determine the…

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the…

Q: If a supply voltage is represented as "single phase, 200 V, 50 Hz" the 200 V is the RMS valu of…

Q: Given the network in the figure below, determine the magnitude of the input voltage Vs. 0.3 0 jo.1 N…

A: Given network,

Q: An AC generator having an internal resistance of 2 k*(omega) is connected to an LCR circuit in…

A: PART (a): The circuit is: Given, L=40π HC=10π μFR=2 kΩr=2 kΩE=282 sin 100πt Vω=100π

Q: d. Write the equation for the power as a function of time. e. You measure the rms current (with a…

A: The given graph is power waveform. What is power equation, voltage equation, current equation.…

Q: Calculate the root-mean-square (rms) value of the current whose waveform is given below. The…

Q: The peak value of the reactive component of power transmitted, that is forever travelling backward…

A: The peak value of the reactive component of power transmitted that is forever travelling backward…

Q: An industrial load consumes 66 kW at a pf of 0.505 lagging from a 480-V rms line. The transmission…

Q: What is the value of real power supplied by the source in the figure? 62 30/0° V rms 42 3031.4 2007…

A: Impedance of the circuit :- 6+(4∥(-j2))=6.8-j1.6=6.98∠-13.24o So current supplied by source =…

Q: A complex voltage given by: v = 250 sin(wt) + 50 sin(3wt + ) + 20 sin(5wt +) is applied to a series…

Q: A dc voltage equal to Vdc V is applied to a resistor of R Ω. Asinusoidal voltage equal to vs V is…

A: Calculating energy delivered to the resistor due to DC voltage source is VDC = Vmax.…

Q: A complex voltage given by: v = 250 sin(wt) + 50 sin(3wt +) + 20 sin(5wt + is applied to a series…

Q: Find the RMS value of the waveform depicted below. Given A = 9, a = 2, b = 8, and T = 13 %D

Q: A 440 V rms source supplies power to a load Z = 10 + j2 through a transmission line having a total…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: A 50 kW load operates from a 60 Hz, 10 kV rms line with a power factor of 0.6 lagging. Determine the…

A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.

Q: Find the rms of the below voltage waveform 2.

A: RMS of AC is that value which when passes through a resistor of known value for a particular…

Q: 62 30/0° V rms -j22 Determine the power factor of the entire circuit of as seen by the source.

A: Power factor is the ratio of true power by apparent power. The value of power factor lies in between…

Q: Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average…

Q: Derive the formula for Average Power, Pavg = VI cosθ watts, where V is the root-mean-square (rms)…

A: To derive the formula for Average power Pavg = VI cosθ watts

Q: If the rms values of voltage and current are 120 V and e A. The instantaneous power is, (a) 120/2…

A: Input =rms =120 V rms current =e-j20=1∠-300Imax=2∠-300 V=1202cosωt+00 Instantaneous power is given…

Q: A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: signal is equal to its RMS value. Which of the following is the correct mathematical representation…

Q: resistor whose resistance is 50Ω is traversed by an alternating current that obeys the function I…

A: The solution is as follows.

Q: Example: Find the rms value for the current waveform shown below: 1 1 3 4 6 t(sec)

A: RMS Value of a signal: It's that steady state equivalent of a time varying signal which would…

Q: The average value of a sinusoidal current is 300A. What is it’s rms value? Group of answer choices…

Q: The voltage across a 50-2 resistive load is the positive portion of a cosine wave. That is, 10 cos…

Q: For the circuit shown below, R 2 2, L 20 mH, and E-100V. The ac source is 120 V rms at 60 Hz. (a)…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 2. The current in an a.c. circuit at any time 't' seconds is given by, i= Im sin (Bat +X) Find (i)…

A: Note :- As per guidelines we are supposed to answer only first 3_sub-parts. So I request you to post…

Q: Compute the rms value of the voltage waveform shown in Fig. v(t) (V) ил. 10 2 4 6 8 t(s)

Q: 36 An industrial assembly hall is continuously lit by one hundred 40-W mercury vapor lamps in…

A: The total power consumed by 100 bulbs is:

Concept explainers

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.

Question

A voltage given by v(t) = 311 cos (311 pi t) V is applied to a 50-ohm resistance. (a.) Sketch v(t) to scale versus time. (b.) Determine the rms value of the voltage and the average power delivered to the resistance. (c.)Determine the power as a function of time and sketch to scale.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

P-channel Metal-Oxide Semiconductor (PMOS), N-channel Metal-Oxide Semiconductor (NMOS), and Complementary Metal-Oxide Semiconductor (CMOS)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
Let a voltage source v(t)=4cos(t+60) be connected to an impedance Z=230. (a) Given the operating frequency to be 60 Hz, determine the expressions for the current and instantaneous power delivered by the source as functions of time. (b) Plot these functions along with v(t) on a single graph for comparison. (c) Find the frequency and average value of the instantaneous power.
Under balanced operating conditions, consider the three-phase complex power delivered by the three-phase source to the three-phase load. Match the following expressions, those on the left to those on the right. (i) Realpower, P3 (a) (3VLLIL)VA (ii) Reactive power, Q3 (b) (3VLLILsin)var (iii) Total apparent power, S3 (c) (3VLLILcos)W (iv) Complex power, S3 (d) P3+jQ3 Note that VLL is the rms line-to-line voltage, IL is the rms line current, and is the power-factor angle.
An example power system has two distinct manufacturing areas, one with harmonic loads, and another with only linear loads. The portion of the system with the harmonic loads draws 75 A rms at 60 Hz, 10 A rms at 300 Hz, and 5 A rms at 420 Hz. The part of the system with only linear loads draws 75 A rms at 60 Hz. (i) What is the total load current (at 60 Hz) if both manufacturing plants are running? Calculate the THD. (ii) What is the total load current (at 60 Hz) if only the manufacturing plant with harmonic loads is running? Calculate the THD.
ESSAY What are the effects of basic electrical components on the average power of the system and what is the concept of power factor.
Calculate the RMS value of the following function
Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags A by p/3 radians and the line current is 23.3 amp, determine the current in B.
1. Determine the RMS values of voltage and current, and the total power absorbed by the circuit element
Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags behind A by pi/3 radians and the line current is 23.4 amp, determine the current in B.
A voltage is given by v( t )=10 sin(1000πt+30°). First, use a cosine function to express v(t). Then, find the angular frequency, the frequency in hertz, the phase angle, the period, and the rms value. Find the power that this voltage delivers to a 50-Ω resistance. Find the first value of time after t=0 that v(t) reaches its peak value. Sketch v(t) to scale versus time. * Denotes that answers are contained in the Student Solutions files. See See Appendix E for more information about accessing the Student Solutions.
calculate the rms value in v of this signal shown below:
A supply voltage v given by v = (240 sin 314t + 40 sin 942t + 30 sin 1570t) volts is applied to a circuit comprising a resistance of 12 ohmconnected in series with a coil of inductance 9.55 mH. Determine (a) an expression to represent the instantaneous value of the current, (b) the rms voltage, (c) the rms current, (d) the power dissipated, and (e) the overall power factor.